manualshive.com logo in svg

Neumann.Berlin KH 150, Инструкция по эксплуатации

Поделиться
Скачать
Neumann.Berlin KH 150 Скачать руководство пользователя страница 35

KH 150 AES67  |  

35

Cleaning and maintaining the loudspeaker

CAUTION

Damage to the product caused by liquids!

Liquids entering the product can cause a short-circuit in the electronics and damage or even destroy the product .

 

X

Keep all liquids away from the product!

 

X

Before cleaning, disconnect the product from the power supply .

 

X

Use a soft, dry, and lint-free cloth to clean the product .

 

X

Be careful not to accidentally adjust the controls when cleaning .

Troubleshooting

Problem

Cause

Solution

The Neumann logo is off, no 
sound is heard from the loud-
speaker .

The loudspeaker’s main 
internal fuse has blown .

Have the product checked by an authorized 
Neumann service partner . There is no plug 
fuse in the device .

The Neumann logo is off or not 
clearly visible, but sound is heard 
from the loudspeaker .

The Neumann logo is 
switched off or dimmed .

Switch on the Neumann logo and switch off 
the dimming (see page 10) .

The loudspeaker is buzzing .

Incorrect wiring in the 
audio cable and/or poor 
quality grounding in the 
audio cable .

Check the cabling, especially if unbalanced 
cabling has been used – see the cable wiring 
diagram on page 7 . Use gold-plated 
connectors . 
Set the output level of the loudspeaker as 
low as possible and set the output level of 
the audio source as high as possible, without 
causing it to clip . 
Set the GROUND LIFT switch to the Lift 
position .

The loudspeaker sounds very 
“thin” in the bass . The low fre-
quency response is very low .

Incorrect wiring in the 
audio cable or adapter .

Check the cabling, especially if unbalanced 
cabling has been used – see the cable wiring 
diagram on page 7 . 

One loudspeaker is out of 
phase with the other . This 
results in cancellation in 
the low frequency range .

Check the cabling, especially if unbalanced 
cabling has been used – see the cable wiring 
diagram on page 7 .

Check the settings in the signal source .

Standby is too sensitive or not 
sensitive enough .

Incorrect standby settings, 
or noise peaks / extraneous 
noise in the source .

Check the standby settings and signal source 
– see “Customizing standby behavior” on 
page 17 .

For further information, please refer to the “Questions & Answers” section on the product page at www .neumann .
com .

EN

Содержание KH 150






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды