manualshive.com logo in svg

Neumann.Berlin KH 150, Инструкция по эксплуатации

Поделиться
Скачать
Neumann.Berlin KH 150 Скачать руководство пользователя страница 20

KH 150 AES67  |  

20

Setting up the AES67 network interface

The loudspeaker features a fully redundant network interface according to ST 2022-7 and can 
be operated in redundant or non-redundant mode . The factory default setting is non-redun-
dant . 

The network interface configuration can be accessed via the built-in web interface of the 
AES67 port . The AES67 configuration can be accessed with any web browser from a PC, Mac or 
any other computer .

The two RJ-45 network sockets of the interface can be operated in non-redundant mode 
(switched mode) or in redundant mode according to ST 2022-7 .

Redundant mode

: both PRIMARY and SECONDARY sockets have the same signal for setting up 

two completely redundant streams in your audio network infrastructure .

Non-redundant mode (switched mode)

: the SECONDARY socket can be used for daisy-chaining 

the signal to the PRIMARY socket of another subwoofer . In that mode the PRIMARY socket of 
the first subwoofer needs to be used for network control .

Default IP addresses of the loudspeaker

The loudspeaker’s network interface has three IP addresses .

Primary address in non-redundant operation (eth0)

The non-redundant primary interface (eth0) is assigned and only used in non-redundant 
mode . This port is used by the AES67 audio and the MA 1 - Automatic Monitor Alignment 
software (PC/Mac)
The factory default is:

IP: 
Mask:

192 .168 .0 .100 
255 .255 .255 .0

Note: be sure to define this IP address in a different subnet compared to the primary IP 
address in redundant mode (see below), even when you are using the loudspeaker in redun-
dant mode .

Primary address in redundant operation (eth1.10)

The redundant primary interface (eth1 .10) is assigned and used in redundant mode . This 
redundant primary port is used by the AES67 primary audio and the NEUMANN network 
control scheme in the MA 1 - Automatic Monitor Alignment software (PC/Mac)
The factory default is:

IP: 
Mask:

192 .168 .10 .100 
255 .255 .255 .0

Note: be sure to define this IP address in a different subnet compared to the primary IP 
address in non-redundant mode (see above), even when you are using the loudspeaker in 
non-redundant mode .

Secondary address in redundant operation (eth2.20)

The redundant secondary interface (eth2 .20) is assigned and used in redundant mode .

This redundant secondary port is used by the AES67 secondary audio .
The factory default is:

IP: 
Mask:

192 .168 .20 .100 
255 .255 .255 .0

NOTE: ensure that these three IP addresses are not in the same subnet as any of the other 
two IP addresses .

EN

Содержание KH 150






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды