NEC V850ES/SA2 UPD703201 Скачать руководство пользователя

Страница: 416 / 518

CHAPTER 13 DMA FUNCTIONS (DMA CONTROLLER)

Preliminary User’s Manual U15905EJ1V0UD

416

13.8 DMA Channel Priorities

The DMA channel priorities are fixed as follows.

DMA channel 0 > DMA channel 1 > DMA channel 2 > DMA channel 3

These priorities are valid in the TI state only. In the block transfer mode, the channel used for transfer is never

switched.

In the single-step transfer mode, if a higher priority DMA transfer request is issued while the bus is released (in the

TI state), the higher priority DMA transfer request is acknowledged.

13.9 DMA Transfer Start Factors

There are two types of DMA transfer start factors, as shown below.

(1) Request from software

If the STGn, Enn, and TCn bits of the DCHCn register are set as follows, DMA transfer starts (n = 0 to 3).

•

STGn bit = 1

•

Enn bit = 1

•

TCn bit = 0

(2) Request from on-chip peripheral I/O

If, when the Enn and TCn bits of the DCHCn register are set as shown below, an interrupt request is issued

from the on-chip peripheral I/O that is set in the DTFRn register, DMA transfer starts (n = 0 to 3).

•

Enn bit = 1

•

TCn bit = 0

13.10 DMA Transfer End

13.10.1 DMA transfer end interrupt

When DMA transfer ends and the TCn bit of the DCHCn register is set to 1, a DMA transfer end interrupt

(INTDMAn) is issued to the interrupt controller (INTC) (n = 0 to 3).

13.10.2 Terminal count output upon DMA transfer end

The terminal count signal becomes active for one clock during the last DMA transfer cycle.

Содержание V850ES/SA2 UPD703201







































































































































































































































































































































































































































































































































Результаты поиска

Содержание V850ES/SA2 UPD703201

Отзывы:

Похожие инструкции для V850ES/SA2 UPD703201

Бренды по названию

Популярные бренды

NEC V850ES/SA2 UPD703201, Руководство пользователя

Результаты поиска

Содержание V850ES/SA2 UPD703201

Отзывы:

Похожие инструкции для V850ES/SA2 UPD703201

Бренды по названию

Популярные бренды