NEC V850ES/SA2 UPD703201 Скачать руководство пользователя

Страница: 193 / 518

CHAPTER 5 BUS CONTROL FUNCTION

Preliminary User’s Manual U15905EJ1V0UD

193

5.6.2

External wait function

To synchronize an extremely slow external device, I/O, or asynchronous system, any number of wait states can be

inserted in the bus cycle by using the external wait pin (WAIT).

Access to each area of the internal ROM, internal RAM, and internal peripheral I/O is not subject to control by the

external wait function, in the same manner as the programmable wait function.

The WAIT signal can be input asynchronously to CLKOUT, and is sampled at the falling edge of the clock in the T2

and TW states of the bus cycle in the multiplexed bus mode. In the separate bus mode, it is sampled at the rising

edge of the clock immediately after the T1 and TW states of the bus cycle. If the setup/hold time of the sampling

timing is not satisfied, a wait state is inserted in the next state, or not inserted at all.

5.6.3

Relationship between programmable wait and external wait

Wait cycles are inserted as the result of an OR operation between the wait cycles specified by the set value of the

programmable wait and the wait cycles controlled by the WAIT pin. In other words, the number of wait cycles is

determined by the side with the greatest number of cycles.

Wait control

Programmable wait

Wait via WAIT pin

For example, if the timing of the programmable wait and the WAIT pin signal is as illustrated below, three wait

states will be inserted in the bus cycle.

Figure 5-3. Example of Inserting Wait States in Separate Bus Mode

CLKOUT

WAIT pin

Wait via WAIT pin

Programmable wait

Wait control

Remark

The circles indicate the sampling timing.

Содержание V850ES/SA2 UPD703201







































































































































































































































































































































































































































































































































Результаты поиска

Содержание V850ES/SA2 UPD703201

Отзывы:

Похожие инструкции для V850ES/SA2 UPD703201

Бренды по названию

Популярные бренды

NEC V850ES/SA2 UPD703201, Руководство пользователя

Результаты поиска

Содержание V850ES/SA2 UPD703201

Отзывы:

Похожие инструкции для V850ES/SA2 UPD703201

Бренды по названию

Популярные бренды