NEC DLP CINEMA NC1600C, Руководство по обслуживанию

Страница: 66 / 382

Important Information
Installation
1. Do not place your Touch panel in direct sunlight, near heaters
or heat radiating appliances.
2. Exposure to direct sunlight, smoke or steam can harm inter-
nal components.
3. Handle your Touch panel carefully. Dropping or jarring can
damage internal components.
4. Do not place heavy objects on top of your Touch panel.
Power Supply
1. Handle the power cable* carefully and avoid excessive bend-
ing. A damaged cord can cause electric shock or fire.
* The following outlines the power cables described in this
document.
• If using the NC2500/NC1500 projector series:
DC power cable packaged with the holder arm
• If using the NC800 projector series:
AC power adapter and AC power cable packaged with
the holder arm
2. If the Touch panel is not to be used for an extended period of
time, disconnect the plug from the power outlet.
3. Do not touch the power plug with wet hand. Doing so can
cause electrical shock or fire.
4. Do not touch the power plug during a thunder storm. Doing
so can cause electrical shock or fire.
Cleaning
1. Cut the power to all connected devices before cleaning.
2. Wipe it with a soft lint-free cloth. In doing so, do not strain the
liquid crystal panel; it may cause a damage.
3. When the panel is badly stained, soak a cloth in neutral detergent
deluted with water, wring it out, and wipe the stain off. As a finishing
touch, wipe the panel with a dry cloth.
When using a chemical dustcloth, follow its instructions.
CAUTION
• Do not have the liquid crystal panel touched with a sharp-pointed
tool such as a mechanical pencil or a screwdriver. Do not press
firmly the surface of the liquid crystal panel or the frame of the
touch panel; they may be scratched or break down.
• Should the liquid crystal panel be damaged, do not put the internal
liquid into your mouth or touch it. If the liquid gets in your mouth,
gargle at once. If the liquid comes in contact with your skin or it
gets in your eye, first rinse your skin or eye with running water for
more than 15 minutes and then see the doctor immediately.
• This machine is designed to monitor and control the projector. Do
not use the machine for other than intended use. Particularly, never
use this machine to make a device which may affect people’s
lives (such as an emergency stop switch).
• To prevent mis-operation, observe the following precautions.
• Do not cut the power to the touch panel while the projector
head is running.
• When performing maintenance, cut the power to all connected
devices.
Disposing of your used product
EU-wide legislation as implemented in each
Member State requires that used electrical and
electronic products carrying the mark (left) must
be disposed of separately from normal
household waste.
This includes projectors and their electrical
accessories or lamps. When you dispose of such
products, please follow the guidance of your
local authority and/or ask the shop where you
purchased the product.
After collecting the used products, they are
reused and recycled in a proper way. This effort
will help us reduce the wastes as well as the
negative impact to the human health and the
environment at the minimum level.
The mark on the electrical and electronic
products only applies to the current European
Union Member States.
For questions relating to unclear points or repairs
Contact your dealer or the following support branches for
questions relating to unclear points, malfunctions and repairs
of the product.
In Europe
NEC Europe, Ltd. / European Technical Centre
Address: Unit G, Stafford Park 12, Telford TF3 3BJ, U.K.
Telephone: +44 1952 237000
Fax Line: +44 1952 237006
In North America
NEC Corporation of America
Digital Cinema Division
Address: 4111 West Alameda Avenue Suite 412 Burbank,
CA 91505
Telephone: +01 818 557 2500
*If the above line is busy, please dial as below:
Telephone: +01 866 632 6431
Fire and Shock Precautions
Prevent foreign objects such as paper clips and bits of pa-
per from falling into your Touch panel. Do not attempt to
retrieve any objects that might fall into your Touch panel. Do
not insert any metal objects such as a wire or screwdriver
into your Touch panel. If something should fall into your Touch
panel, disconnect it immediately and have the object re-
moved by a qualified service personnel.
E-2