Nautel XR12 Скачать руководство пользователя страница 17

Страница: 17 / 92

XR12 Installation Manual

Preparing for installation

Issue 3.0 2009-07-15

Page 1-1

Section 1:

Preparing for installation

Before installing your XR12 transmitter, perform the following steps:

1. Ensure that you have performed the pre-installation tasks described in the

XR12 Pre-installation Manual

2. Make sure that you received all the components. (Check your packing list.)

3. Inspect all crates and packages for damage.

4. Report any damage immediately to your Nautel sales representative and the carrier.

5. Move the crates as close as possible to the transmitter’s planned location.

6. Unpack the crates in accordance with the instructions provided on the outside of the crates.

•

For each crate, remove the panel labelled

open this side

. The panel is attached using

Philips head screws.

•

Remove any visible packing material, including braces, from the crate's interior.

7. Review any assembly notes or instructions contained inside the transmitter crates. (For sites

requiring custom configurations, the instructions provided with the transmitter replace the
instructions provided here.)

8. Assemble your parts and tools.

For a list of required tools, see

“Parts and tools” on page 12-1

9. When you are ready to install the XR12 transmitter, follow the steps shown in

Figure 1.1 on

page 1-2

TIP

When you have completed a task or step, put a check mark beside the step
number.

CAUTION:
FAILURE TO COMPLY WITH RECOMMENDATIONS MAY VOID YOUR MANUFACTURER’S
WARRANTY. FOR MORE INFORMATION, REVIEW YOUR WARRANTY DOCUMENTS.

Содержание XR12





























































































Результаты поиска

Содержание XR12

Отзывы:

Похожие инструкции для XR12

Бренды по названию

Популярные бренды

Nautel XR12, Руководство по установке

Результаты поиска

Содержание XR12

Отзывы:

Похожие инструкции для XR12

Бренды по названию

Популярные бренды