National Instruments Network Adapter NI PXIe-1075 Скачать руководство пользователя | Manualshive

Страница: 26 / 78

background image

Chapter 2

Installation and Configuration

NI PXIe-1075 User Manual

2-6

ni.com

If your power outlet does not have an appropriate ground connection, you
must connect the premise safety ground to the chassis grounding screw
located on the rear panel. Refer to Figure 1-2,

Rear View of the

NI PXIe-1075 Chassis

, to locate the chassis grounding screw. To connect

the safety ground, complete the following steps:

1.

Connect a 16 AWG (1.3 mm) wire to the chassis grounding screw
using a grounding lug. The wire must have green insulation with a
yellow stripe or must be noninsulated (bare).

2.

Attach the opposite end of the wire to permanent earth ground using
toothed washers or a toothed lug.

Connecting to Power Source

Caution

Do

not

install modules prior to performing the following power-on test.

To completely remove power, you

must

disconnect the AC power cable.

Attach input power through the rear AC inlet using the appropriate
AC power cable supplied. Refer to Figure 1-2,

Rear View of the

NI PXIe-1075 Chassis

, to locate the AC inlet.

The Inhibit Mode switch allows you to power on the chassis or place it in
standby mode. Set the Inhibit Mode switch on the back of the chassis to the

Manual

position. Observe that all fans become operational and the power

switch LED is a steady green. Switching the Inhibit Mode switch to the

Default

position allows the system controller to control the power supply.

Installing a PXI Express System Controller

This section contains general installation instructions for installing a
PXI Express system controller in a NI PXIe-1075 chassis. Refer to your
PXI Express system controller user manual for specific instructions and
warnings. To install a system controller, complete the following steps:

1.

Inspect the slot 1 pins on the chassis backplane for any bending or
damage prior to installation.

2.

Connect the AC power source to the PXI Express chassis before
installing the system controller. The AC power cord grounds the
chassis and protects it from electrical damage while you install the
system controller.

«
...
24
25
26
27
28
...
»

Содержание Network Adapter NI PXIe-1075















































































Отзывы:

Нет отзывов

Похожие инструкции для Network Adapter NI PXIe-1075

Бренд: Orban Страницы: 255

Kinetic FLT 80 D5/DDC Body

Бренд: EK-Quantum Страницы: 16

ELITENAS EN104L+(B)

Бренд: Sans Digital Страницы: 9

SteelCentral AppResponse 2180

Бренд: Riverbed Страницы: 82

Бренд: Sony Ericsson Страницы: 93

COM Express conga-TC87

Бренд: Congatec Страницы: 114

Бренд: Kontron Страницы: 32

NC-MCO - TECHNICAL

Бренд: Crest Audio Страницы: 2

Бренд: Alphacool Страницы: 9

BPN-SAS3-LB16A-N10

Бренд: Supermicro Страницы: 11

Бренд: IBM Страницы: 242

Бренд: Devolo Страницы: 24

Бренд: Idex Страницы: 4

Schoeps electret

Бренд: VAMISOUND Страницы: 15

Бренд: Johnson Controls Страницы: 20

Бренд: Johnson Controls Страницы: 40

Бренд: JVC Страницы: 26

Бренд: Nokia Страницы: 111

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды