National Instruments Network Adapter NI PXIe-1075 Скачать руководство пользователя

Страница: 71 / 78

Glossary

NI PXIe-1075 User Manual

G-4

ni.com

in.

Inches.

inhibit

To turn off.

jitter

A measure of the small, rapid variations in clock transition times from their
nominal regular intervals. Units: seconds RMS.

Kilograms.

Kilometers.

Pounds.

LED

Light emitting diode.

line regulation

The maximum steady-state percentage that a DC voltage output will
change as a result of a specified change in input AC voltage (step change
from 90 to 132 VAC or 180 to 264 VAC).

load regulation

The maximum steady-state percentage that a DC voltage output will
change as a result of a step change from no-load to full-load output current.

Meters.

MHz

Megahertz. One million Hertz; one Hertz equals one cycle per second.

Miles.

Milliseconds.

MTBF

Mean time between failure.

MTTR

Mean time to repair.

Содержание Network Adapter NI PXIe-1075















































































Результаты поиска

Содержание Network Adapter NI PXIe-1075

Отзывы:

Похожие инструкции для Network Adapter NI PXIe-1075

Бренды по названию

Популярные бренды

National Instruments Network Adapter NI PXIe-1075, Руководство пользователя

Результаты поиска

Содержание Network Adapter NI PXIe-1075

Отзывы:

Похожие инструкции для Network Adapter NI PXIe-1075

Бренды по названию

Популярные бренды