National Instruments Network Adapter NI PXIe-1075 Скачать руководство пользователя | Manualshive

Страница: 33 / 78

background image

Chapter 2

Installation and Configuration

©

National Instruments Corporation

2-13

NI PXIe-1075 User Manual

(pin 5) to a Logic Ground pin (pin 1 or 9). As long as this connection exists,
the chassis will remain off (standby); when you remove this connection, the
chassis turns on.

Note

For the Remote Inhibit signal to control the On/Off (standby) state of the chassis, the

Inhibit Mode switch must be in the

Manual

position.

PXI_CLK10 Rear Connectors

There are two BNC connectors on the rear of the NI PXIe-1075 chassis for
PXI_CLK10, as shown in Figure 1-2,

Rear View of the NI PXIe-1075

. The connectors are labeled IN and OUT. You can use them for

supplying the backplane with PXI_CLK10 or routing the backplane’s
PXI_CLK10 to another chassis. Refer to the

System Reference Clock

section of Chapter 1,

Getting Started

, for details about these signals.

PXI Express System Configuration with MAX

The PXI Platform Services software included with your chassis
automatically identifies your PXI Express system components to generate
a

pxiesys.ini

file. You can configure your entire PXI system and

identify PXI-1 chassis through Measurement & Automation Explorer
(MAX), included with your system controller. MAX creates the

pxiesys.ini

and

pxisys.ini

files, which define your PXI system

parameters. MAX also provides an interface to route and reserve triggers
so dynamic routing, through drivers such as DAQmx, avoids
double-driving and potentially damaging trigger lines. For more
information about routing and reserving PXI triggers, refer to
KnowledgeBase 3TJDOND8 at

ni.com/support

.

The configuration steps for single or multiple-chassis systems are the same.

«
...
31
32
33
34
35
...
»

Содержание Network Adapter NI PXIe-1075















































































Отзывы:

Нет отзывов

Похожие инструкции для Network Adapter NI PXIe-1075

Бренд: Patton electronics Страницы: 51

Бренд: ICP DAS USA Страницы: 8

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

Бренд: Moxa Technologies Страницы: 19

Бренд: vPipes Страницы: 3

Converter Board R0E5212BACFG00

Бренд: Renesas Страницы: 6

OP-8000-EDFA-1U Series

Бренд: Optostar Страницы: 9

UniFi Cloud Key

Бренд: Ubiquiti Страницы: 13

Бренд: Advantech Страницы: 50

Бренд: Giacomini Страницы: 2

Бренд: DigiTech Страницы: 6

Бренд: MSNswitch Страницы: 2

Бренд: Supermicro Страницы: 131

Бренд: PADAUK Страницы: 27

Бренд: Kontron Страницы: 14

Бренд: XMOS Страницы: 8

Бренд: Rosewill Страницы: 5

Бренд: ADLINK Technology Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды