National Instruments AT-MIO/AI E Series Скачать руководство пользователя | Manualshive

Страница: 73 / 181

background image

Chapter 4 Signal Connections

AT-MIO/AI E Series User Manual

4-24



National Instruments Corporation

Single-Ended Connection Considerations

A single-ended connection is one in which the AT E Series board
analog input signal is referenced to a ground that can be shared with
other input signals. The input signal is tied to the positive input of the
PGIA, and the ground is tied to the negative input of the PGIA.

When every channel is configured for single-ended input, up to 16
analog input channels are available (up to 64 channels on the
AT-MIO-64E-3).

You can use single-ended input connections for any input signal that
meets the following conditions:

•

The input signal is high level (greater than 1 V).

•

The leads connecting the signal to the AT E Series board are less

than 10 ft (3 m).

•

The input signal can share a common reference point with other

signals.

DIFF input connections are recommended for greater signal integrity
for any input signal that does not meet the preceding conditions.

You can software configure the AT E Series board channels for two
different types of single-ended connections—RSE configuration and
NRSE configuration. The RSE configuration is used for floating signal
sources; in this case, the AT E Series board provides the reference
ground point for the external signal. The NRSE input configuration is
used for ground-referenced signal sources; in this case, the external
signal supplies its own reference ground point and the AT E Series
board should not supply one.

In single-ended configurations, more electrostatic and magnetic noise
couples into the signal connections than in differential configurations.
The coupling is the result of differences in the signal path. Magnetic
coupling is proportional to the area between the two signal conductors.
Electrical coupling is a function of how much the electric field differs
between the two conductors.

«
...
71
72
73
74
75
...
»

Содержание AT-MIO/AI E Series






















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT-MIO/AI E Series

Бренд: Datasat Страницы: 170

Бренд: CSS Страницы: 2

Linear SCP-LT8362-S-EVALZ

Бренд: Analog Devices Страницы: 8

Бренд: Baldor Страницы: 34

Бренд: Variscite Страницы: 18

Бренд: HighPoint Страницы: 10

EK-FC980 GTX Classy

Бренд: ekwb Страницы: 2

zoomno MSC-5578

Бренд: BIIZZY Страницы: 2

Бренд: Bailey Страницы: 33

Бренд: Raven Страницы: 33

High-Precision AD/DA Board

Бренд: Waveshare Страницы: 8

Бренд: ETAS Страницы: 29

Wisenet PRN-6400DB4

Бренд: Hanwha Techwin Страницы: 125

Бренд: Lanner Страницы: 99

Бренд: National Instruments Страницы: 147

System 4 Landmark Technic Processor

Бренд: Ametek Land Страницы: 34

Бренд: Stepper Motor Canada Страницы: 7

9500S-8 - Escalade RAID Controller

Бренд: 3Ware Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды