National Instruments AT-MIO/AI E Series Скачать руководство пользователя | Manualshive

Страница: 69 / 181

background image

Chapter 4 Signal Connections

AT-MIO/AI E Series User Manual

4-20



National Instruments Corporation

Differential Connection Considerations (DIFF Input Configuration)

A differential connection is one in which the AT E Series board analog
input signal has its own reference signal or signal return path. These
connections are available when the selected channel is configured in
DIFF input mode. The input signal is tied to the positive input of the
PGIA, and its reference signal, or return, is tied to the negative input of
the PGIA.

When you configure a channel for differential input, each signal uses
two multiplexer inputs—one for the signal and one for its reference
signal. Therefore, with a differential configuration for every channel,
up to eight analog input channels are available (up to 32 channels on the
AT-MIO-64E-3).

You should use differential input connections for any channel that
meets any of the following conditions:

•

The input signal is low level (less than 1 V).

•

The leads connecting the signal to the AT E Series board are

greater than 10 ft (3 m).

•

The input signal requires a separate ground-reference point or

return signal.

•

The signal leads travel through noisy environments.

Differential signal connections reduce picked-up noise and increase
common-mode noise rejection. Differential signal connections also
allow input signals to float within the common-mode limits of the
PGIA.

«
...
67
68
69
70
71
...
»

Содержание AT-MIO/AI E Series






















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT-MIO/AI E Series

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 30

Бренд: Aleratec Страницы: 12

Бренд: BSS Audio Страницы: 20

Бренд: Reeven Страницы: 2

Бренд: Xilica Audio Design Страницы: 30

Бренд: Eaton Страницы: 14

Digital Encoder Plus

Бренд: IDT Страницы: 98

Бренд: Aaeon Страницы: 61

Бренд: Idis Страницы: 17

PFC Chokes PFC3515V Series

Бренд: Delta Electronics Страницы: 1

Бренд: Compal Страницы: 47

Бренд: Alcatel-Lucent Страницы: 60

Tamar FCSAS102800

Бренд: Bridgeworks Страницы: 56

Бренд: DFRobot Страницы: 30

Бренд: Cypress Semiconductor Страницы: 26

Бренд: Renesas Страницы: 4

Бренд: Intel Страницы: 44

Бренд: Alphacool Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды