National Flooring Equipment 8000 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 68

National Flooring Equipment 8000 Скачать руководство пользователя страница 27

Machine Maintenance

27

CHANGING HYDRAULIC FLUID FILTER

1. Remove

old

fi

lter by turning counter-clockwise. Have rag ready to catch excess

fl

uid that may spill.

2. Install

new

fi

lter on by turning clockwise.

SWITCHES

There are two switches:

•

On (Key) Switch

• Seat

Switch

Caution: Do not disable switches

SEAT REPLACEMENT

1.  Remove two (2) knobs on each side of the hood (4 times).
2.  Slightly raise seat plate & unplug wire harness.
3.  Lift hood all the way back to the hood bumpers.
4. Remove

seat.

5. To replace seat, set seat on top of hood.
6. Replace the four 5/16 button hexhead screws from underneath the hood.
7. Firmly

tighten.

8. Reconnect back-up beeper and seat switch wires.
9. Replace hood and screws.

CASTER MAINTENANCE

1. Keep clean and free of debris, make sure it can move freely.
2. Give a shot of grease in grease zerc on caster every six months to keep moving

freely.

3. To remove caster, machine will need to be raised. Push the cylinder lift lever for-

ward to lower and adjust the angle of the cutting head to jack up the machine (See
Figure VV). Block up machine (See Figure WW). Remove four bolts, pull caster off,
clean/replace as needed.

4. Replace

caster.

5. Replace

and

fi

rmly tighten the four bolts.

6. Lower the machine.

NOTE: A SPACER IS NEEDED WITH CASTER WHEN USING AN 18 INCH WHEEL.

FIG. VV

FIG. WW

CAUTION:

THE BACKUP BEEPER IS ON THE MACHINE FOR SAFETY. IT IS

IMPORTANT TO KEEP IT IN GOOD WORKING CONDITION. FAILURE TO DO SO
COULD CAUSE BODILY INJURY.

Fax: 763-535-8255

[email protected]

«
...
25
26
27
28
29
...
»

Содержание 8000





































































Отзывы:

Нет отзывов