National Flooring Equipment 8000 Скачать руководство пользователя страница 19

Страница: 19 / 68

Machine Operation

CAUTION:

NEVER CHANGE CUTTING HEAD OR SERVICE BLADES WHILE MACHINE IS RUNNING.

WARNING:

DISARM MACHINE WHEN MACHINE IS NOT IN USE. REMOVE THE CUTTING HEAD OR DROP CUTTING HEAD TO THE

FLOOR. FAILURE TO DO SO COULD CAUSE SEVERE BODILY INJURY.

Fax: 763-535-8255

[email protected]

DOUBLE STICK CARPET SET-UP

Slide plate should be set low, slide plate should be set to the lowest setting or approximately 2.5 cm (1”) off the

oor. It is best to test to see

which is the easiest way to remove double stick. Start with a Cutting Head from 25.4 to 35.5 cm (10” to 14”) with Self-Scoring Blades. If self-
scoring blades do not work, score thru the carpet the width of the blade (Standard Blade) and scrape up. In some cases, carpet might pull off
the pad and then scrape up the pad separately. Usually leaving carpet connected to the pad works the best. Sharp blades are necessary for
proper operation.

VCT TILE SET-UP

Slide plate should be set low, slide plate should be set to the lowest setting or approximately 2.5 cm (1”) off the

oor. If goods come up easily,

change to a larger Cutting Head. If goods come up harder, use a Cutting Head from 6” to 8” with a Premium High Tempered Blade (.062) to
match cutting head size. Sometimes a .094 blade may work better. If goods remove easily, a Tile Box #7074 can be used. A tile box also works
for wind rowing, assists for a fast clean-up and collection of tile debris for quick removal.

RUBBER TILE SET-UP

Slide plate should be set low, slide plate should be set to the lowest setting or approximately 2.5 cm (1”) off the

oor. Use a Cutting Head from

15.25 to 35.5 cm (6” to 14”) with self-scoring blades or use ditching method with a

at blade (see page 20).

RE-SCRAPING SET-UP

Slide plate should be set high, approx 15.25 cm (6’’) off the

oor. Use a Cutting Head from 20.3 to 68.6 cm (8” to 27”) with Scraper Blades to

match cutting head size. A 38.1 cm (15”) scrapper blade would use a 35.5 cm (14”) Cutting Head. Razor Blades are faster but a Cutting Head
from 20.3 to 35.5 cm (8” to 14”) can be used with a Standard Blade. Flip head regularly.

THIN COATING SET-UP

Slide plate could be set to the low or high setting off the

oor. Test to see which works best. Use a Cutting Head from 20.3 to 68.6 cm (8” to 27”)

with Razor Blades to match cutting head size.

WORKING OVER CONCRETE

Blade should be bevel up when working over concrete. Pretty much anything over concrete works. Try different set-ups to see which works
best. If goods come up dif

cult, slide plate should be at a low setting, slide plate should be set to the lowest setting or approximately 2.5 cm (1”)

off the

oor. Use a smaller size blade. If goods come up easily, a wider blade can be used.

WORKING OVER WOOD

A heavy machine cannot be used on wood sub

oors or raised panel computer

oors. Keep machine light, remove all weights. A weighted ma-

chine could break through the

oor. Slide plate should be set low, slide plate should be set to the lowest setting or approximately 2.5 cm (1”) off

the

oor. Blades should be as

at of an angle as possible. Use a “shoe blade”, Extra Heavy Duty Blade (these blades have a bend to them) or a

regular blade, bevel up. When using a regular blade, bending up the corners of the blade will help prevent the blade from digging into the

oor.

Sometimes a shank blade or a shank blade with a carbide tip will work. Allow blade to shear material from the

oor. The trick on wood

oors is

to run the blade

at. Approach should be at a 45° angle to the board. This keeps from digging into the board and hanging up at the seams.

WORKING OVER SOFT SUB-FLOOR

Slide plate should be set low, slide plate should be set to the lowest setting or approximately 2.5 cm (1”) off the

oor. Blades should be as

at of

an angle as possible. Use a “shoe blade”, Extra Heavy Duty Blade (these blades have a bend to them) or a regular blade, bevel up. When using
a regular blade, bending up the corners of the blade will help prevent the blade from digging into the

oor. Sometimes a shank blade or a shank

blade with a carbide tip will work.

NOTE:

WHEN REMOVING CARPET FROM OVER VCT TILE AND THE TILE NEEDS TO BE SAVED, RUN THE MACHINE AT A 45 ° ANGLE OVER THE TILE.

THIS SHOULD HELP TO SAVE THE FILE.