background image

National Cycle, Inc.

 PO Box 158 Maywood, IL 60153-0158 USA

P: 708-343-0400 / F: 708-343-0625 / E: [email protected]

www.nationalcycle.com

©2021 National Cycle, Inc.

Page 13 of 13

10-118625-000   03/21

CLEANING AND MAINTENANCE

 

To clean your windshield, wash with a clean soft cloth and plenty of warm water and, 
if necessary, a non-abrasive soap such as dishwashing liquid. Flannel or soft cham-
ois make good cleaning cloths. 

Paint, glue residue or grease removal:

 Moisten 

cotton wad with naphtha or turpentine followed by a wash as above. 

National Cycle 

Shield Wash™

 (N1401-01) makes a good daily cleaner and comes 

with a handy travel-size bottle. Shield Wash is safe for all windshields and helmet 
visors.  

Do not clean polycarbonate in hot sun or high temperatures. Do not clean the screen 
with household glass cleaners. 

Do not allow brake fluid, alcohol, or strong solvents to contact the windshield. 

RAIN REPELLENT

 

Do not use rain protective products made for glass. We recommend National Cycle’s 

RainZip®

 (N1410-01) to keep your windshield clear in rainy weather.

National Cycle 3-Year Limited Warranty

 

Register Your Windshield Online at www.nationalcycle.com 

National Cycle hereby warrants to the original registered owner of a National Cycle polycarbonate windshield for a period of three years 
from the date of purchase against breakage. This limited warranty is expressly limited to the replacement of the polycarbonate windscreen. 
This limited warranty does not include scratches, coating failure, cosmetic wear and tear, replacement of hardware, or any consequential 
damages or expenses including labor cost of installation, removal and/or replacement, inconvenience, inbound freight expenses or damage 
to any other component of the vehicle or any other accessories. Certain chemicals, generally known as acidic hydrocarbons, are known to 
cause polycarbonate damage and will not be covered under this limited warranty. Please refer to the cleaning instructions supplied with all 
National Cycle windshields. 

Visit www.nationalcycle.com for further details or call or write National Cycle Inc.

Never operate your vehicle with loose accessory mounting hardware. Check the hardware for tightness regularly. 

UTVs are built with enough frame rigidity to withstand the moderate loads imposed on them by the foreseeable addition of an accessory(ies). If an accessory(ies) 
adversely affects your vehicle’s stability, immediately remove the accessory(ies). Do not operate a vehicle that exhibits unsafe handling traits. 

Have experienced service personnel correct any problem before driving with the accessory(ies) installed. For further questions concerning handling problems associat-
ed with an accessory(ies), contact your dealer, UTV manufacturer, or accessory manufacturer.  

Sunlight reflected off the inside curvature of the windshield can, at certain times of the day, cause extreme heat buildup on the vehicle’s instruments and possibly even 
melt them. Exercise care in parking to avoid this. Park your vehicle facing the sun, or place an opaque object over the instruments and dash panel.

Ask for Shield Wash™ and RainZip® at your local dealer or visit 
www.nationalcycle.com.

WARNING

Содержание Quantum hardcoated N30214-WK














Отзывы: