Nashuatec Aficio 9005 Скачать руководство пользователя страница 35

Страница: 35 / 177

Copying

DDDD

Place originals.

Reference

See p.10 “Placing Originals”.

EEEE

Make the desired settings.

FFFF

Enter the required number of copies using the number keys.

Note

❒

The maximum copy quantity can be set between 1 and 9999 (default:

9999

See p.131 “Max. Number of Sets”.

GGGG

Press the

{{{{

Start

}}}}

key.

The machine starts copying.

Note

❒

When placing an original on the exposure glass or in the ADF using batch
or SADF mode, press the

{{{{

}}}}

key after all have been scanned.

Reference

You can select to have copies delivered either face up or face down. See
p.144 “Eject Copy Face Up/Down in Glass” in “Input Output”.

How to Operate

❖

To stop the machine during a multi-copy run.

Press the

{{{{

Stop

}}}}

key.

❖

To return the machine to the default condition after copying.

Press the

{{{{

Clear Modes

}}}}

key.

❖

When clearing entered values.

Press the

{{{{

Clear

}}}}

key, or

[

Clear

]

on the display.

❖

To confirm settings.

Press the

{{{{

Check Modes

}}}}

key.

BelliniC2_GBcopy_F_FM.book Page 22 Wednesday, December 11, 2002 3:47 PM

Содержание Aficio 9005


















































































































































































Результаты поиска

Содержание Aficio 9005

Отзывы:

Похожие инструкции для Aficio 9005

Бренды по названию

Популярные бренды

Nashuatec Aficio 9005, Руководство по эксплуатации

Результаты поиска

Содержание Aficio 9005

Отзывы:

Похожие инструкции для Aficio 9005

Бренды по названию

Популярные бренды