Nashuatec Aficio 9005 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 177

background image

Introduction

This manual contains detailed instructions on the operation and maintenance of this machine. To get
maximum versatility from this machine all operators should carefully read and follow the instructions in
this manual. Please keep this manual in a handy place near the machine.

Notes

Some illustrations may be slightly different from your machine.

Certain options may not be available in some countries. For details, please contact your local dealer.

Warning:

Use of controls or adjustment or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.

Notes:

The model names of the machines do not appear in the following pages. Check the type of your ma-
chine before reading this manual. (For details,

⇒

p.2 “Machine Types”.)

•

Type1: 9005

•

Type2: 10515

Certain types might not be available in some countries. For details, please contact your local dealer.

Two kinds of size notation are employed in this manual. With this machine refer to the metric version.

For good copy quality, Nashuatec recommends that you use genuine Nashuatec toner.

Nashuatec shall not be responsible for any damage or expense that might result from the use of parts
other than genuine Nashuatec parts in your Nashuatec office product.

Power Source

220 - 240V, 50/60Hz, 16A

Please be sure to connect the power cord to a power source as above. For details about power source,
see “Power Connection” in General Settings Guide.

For safe and correct use of this machine, please be sure to read the Safety Information in the General
Settings Guide before you use it.

BelliniC2_GBcopy_F_FM.book Page 1 Wednesday, December 11, 2002 3:47 PM

«
1
2
3
4
...
»

Содержание Aficio 9005


















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aficio 9005

Бренд: Wasp Страницы: 2

Бренд: Oki Страницы: 197

Бренд: Xerox Страницы: 418

Бренд: FujiFilm Страницы: 37

Бренд: Oce Страницы: 340

Бренд: Muratec Страницы: 112

Бренд: Oce Страницы: 209

Line Printer VIII

Бренд: Radio Shack Страницы: 54

Бренд: Oce Страницы: 330

Бренд: Oki Страницы: 336

Бренд: AstroJet Страницы: 32

Бренд: Oki Страницы: 132

Бренд: Konica Minolta Страницы: 8

Бренд: Savin Страницы: 132

Бренд: SPRT Страницы: 21

Бренд: Gestetner Страницы: 144

Бренд: Oki Страницы: 309

Бренд: BT Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды