Nashuatec Aficio 9005 Скачать руководство пользователя страница 134

Страница: 134 / 177

If You Cannot Make Copies As You Want

121

If You Cannot Make Copies As You Want

This section explains causes and remedies when copy results are not as expect-
ed.

❖

Basic

❖

Edit

Problem

Causes

Solutions

Copies are not stapled.

There are staples jammed
in the stapler.

Remove jammed staples. See

Gener-

al Settings Guide

The number of copies ex-
ceeds the capacity of the
stapler.

Check the stapler capacity. See p.152
“Staple”.

Copy paper is curled.

Turn the copy paper over in the
tray.

Staples are wrongly posi-
tioned.

Originals are not set cor-
rectly.

Check the correct position to place
the originals. See p.49 “Staple”.

You cannot combine sever-
al functions.

Selected functions cannot
be used together.

Check the combination of functions
and make the settings again.

Reference

p.147 “Combination Chart”

Paper frequently jams.

The paper size setting is in-
correct.

Set the paper size correctly. See “Pa-
per Tray Settings”,

General Settings

Guide

Check that the side fences and back
fence are set in the paper tray.

Originals jam.

Different size originals are
placed in the ADF.

Set the Mixed 1&2 Sided function.
See p.73 “Mix 1 & 2 Sided”.

Problem

Causes

Solutions

In Double Copies mode,
parts of the original image
are not copied.

The combination of origi-
nal and copy paper is not
correct.

Select A3

(11"

17"

) for A4

11"

) originals and A4

11"

) for A5

) originals.

In Border, or Center/Bor-
der mode, parts of the orig-
inal image are not copied.

You set a wide erased mar-
gin.

Make the margin width narrower.
You can adjust it between 2–99 mm
(0.1"–3.9"). See p.137 “Erase Border
Width”and p.137 “Erase Centre
Width”.

Originals are not scanned
correctly.

Place the originals correctly.

BelliniC2_GBcopy_F_FM.book Page 121 Wednesday, December 11, 2002 3:47 PM

Содержание Aficio 9005


















































































































































































Результаты поиска

Содержание Aficio 9005

Отзывы:

Похожие инструкции для Aficio 9005

Бренды по названию

Популярные бренды

Nashuatec Aficio 9005, Руководство по эксплуатации

Результаты поиска

Содержание Aficio 9005

Отзывы:

Похожие инструкции для Aficio 9005

Бренды по названию

Популярные бренды