Nashuatec Aficio 9005 Скачать руководство пользователя страница 149

Страница: 149 / 177

User Tools (Copier/Document Server Features)

136

Reproduction Ratio

❖

Preset Reduce/Enlarge

You can set the Reduce/Enlarge ratios first displayed.

❖

Preset Reduce/Enlarge Priority

You can select a Reduce/Enlarge ratio that is detected as priority in preset Re-
duce/Enlarge mode.

❖

Shortcut R/E

You can register up to two frequently used Reduce/Enlarge ratios other than
the fixed Reduce/Enlarge ratio and have them shown on the initial display.
You can also change registered Reduce/Enlarge ratios.

❖

Create Margin Ratio

You can set a Reduce/Enlarge ratio when registering “Create Margin” in a
shortcut key.

Note

❒

You can enter a ratio between 90 and 99 (in increments of 1%) using the
number keys.

Edit

❖

Copy Back Cover

When copying the back cover, you can specify to have the back cover outside
(outside page) or inside (inside page).

❖

Front Page Margin : Left/Right

You can specify left and right margins on the front side of copies in Margin
Adjust mode.

Note

❒

You can enter a margin width of between 0 and 30 mm in 1 mm increments
(0 inch and 1.2 inch in 0.1 inch steps) using the number keys.

❖

Back Side Margins : Left/Right

You can specify left and right margins on the back side of copies in Margin
Adjust mode.

Note

❒

You can enter a margin width of between 0 and 30 mm in 1 mm increments
(0 inch and 1.2 inch in 0.1 inch increments) using the number keys.

BelliniC2_GBcopy_F_FM.book Page 136 Wednesday, December 11, 2002 3:47 PM

Содержание Aficio 9005


















































































































































































Результаты поиска

Содержание Aficio 9005

Отзывы:

Похожие инструкции для Aficio 9005

Бренды по названию

Популярные бренды

Nashuatec Aficio 9005, Руководство по эксплуатации

Результаты поиска

Содержание Aficio 9005

Отзывы:

Похожие инструкции для Aficio 9005

Бренды по названию

Популярные бренды