Nashuatec Aficio 9005 Скачать руководство пользователя

Страница: 136 / 177

If You Cannot Make Copies As You Want

123

❖

Stamp

When Memory Is Full

When using 1 Sided Com-
bine or 2 Sided Combine,
copy is made Top to Bot-
tom even though From Left
to Right is selected.

The orientation of the orig-
inals is incorrect.

Place the originals in the correct ori-
entation. See p.10 “Original Orienta-
tion” .

Problem

Causes

Solutions

The stamp position is
wrong.

The paper orientation is
wrong.

Check the paper orientation and
stamp position.

Nothing is stamped.

The stamp size is larger
than the paper size.

Set the stamp size appropriately.

The stamp text in back side
copy is not stamped in Du-
plex mode.

The back side stamp posi-
tion is incorrect with the
paper size.

Reset the back side stamp position.
See p.143 “Back Side Stamp Position
in Duplex”.

Message

Causes

Solutions & Reference

Memory is full.

Copying will be
stopped.

Press

[

Print

]

to copy

the scanned origi-
nals.

Do not remove the re-
maining originals.

Note

❒

Copying will stop and this
message will be displayed
when memory is full.

The scanned original exceeds
the number of pages that can
be stored in memory.

Press

[

Output

]

to copy scanned

originals and clear the scan-
ning data. Press

[

Print Inquiry

List

]

to clear the scanning data

and not copy.

Press

[

Resume

]

to con-

tinue.

The machine checks if the re-
maining original should be
copied, after the scanned orig-
inal has been printed.

To continue copying, remove
all copies, then press

[

Re-

sume

]

. To stop copying, press

[

Stop

]

Problem

Causes

Solutions

BelliniC2_GBcopy_F_FM.book Page 123 Wednesday, December 11, 2002 3:47 PM

Содержание Aficio 9005


















































































































































































Результаты поиска

Содержание Aficio 9005

Отзывы:

Похожие инструкции для Aficio 9005

Бренды по названию

Популярные бренды

Nashuatec Aficio 9005, Руководство по эксплуатации

Результаты поиска

Содержание Aficio 9005

Отзывы:

Похожие инструкции для Aficio 9005

Бренды по названию

Популярные бренды