Nashuatec Aficio 9005 Скачать руководство пользователя страница 133

Страница: 133 / 177

Troubleshooting

120

If You Cannot Make Clear Copies

Problem

Causes

Solutions

Copies appear dirty.

The image density is too dark. Adjust the image density. See

p.33 “Adjusting Copy Image
Density”.

Auto Image Density is not se-
lected.

Select Auto Image Density.

The reverse side of an original
image is copied.

The image density is too dark. Adjust the image density. See

p.33 “Adjusting Copy Image
Density”.

Auto Image Density is not se-
lected.

Select Auto Image Density.

A shadow appears on copies
when copying pasted origi-
nals.

The image density is too dark. Adjust the image density. See

p.33 “Adjusting Copy Image
Density”.

Change the orientation of the
original.

Fix mending tape to the past-
ed part.

The same copy area is dirty
whenever making copies.

The exposure glass or the ADF
belt is dirty.

Clean them. See “Maintaining
Your Machine”,

General Set-

tings Guide

Copies are too light.

The image density is too light. Adjust the image density. See

p.33 “Adjusting Copy Image
Density”.

Damp or rough grain copy pa-
per is being used.

Use dry paper without a
rough grain.

Toner cartridge is almost emp-
ty.

Add toner. See “Replacing
Toner”,

General Settings

Guide

Parts of the image are not cop-
ied.

The original is not set correct-
ly.

Place originals correctly. See
p.7 “Placing Originals”.

An incorrect paper size is se-
lected.

Select the proper paper size.

Copies are blank.

The original is not set correct-
ly.

Place originals correctly. See
p.7 “Placing Originals”.

A moiré pattern is produced
on copies.

Original has a dot pattern im-
age or many lines.

Place the original on the ex-
posure glass at a slight angle.

;

;;

;

;;

;

BelliniC2_GBcopy_F_FM.book Page 120 Wednesday, December 11, 2002 3:47 PM

Содержание Aficio 9005


















































































































































































Результаты поиска

Содержание Aficio 9005

Отзывы:

Похожие инструкции для Aficio 9005

Бренды по названию

Популярные бренды

Nashuatec Aficio 9005, Руководство по эксплуатации

Результаты поиска

Содержание Aficio 9005

Отзывы:

Похожие инструкции для Aficio 9005

Бренды по названию

Популярные бренды