background image

W415-1066 / A / 03.06.12

42

10.0  wArrANTy

NAPOLEON® warrants its products against manufacturing defects to the original purchaser only. registering your warranty is not 

necessary. Simply provide your proof of purchase along with the model and serial number to make a warranty claim. NAPOLEON® 

reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim. Provided that the 

purchase was made through an authorized NAPOLEON® dealer your appliance is subject to the following conditions and limitations:

warranty coverage begins on the date of original installation.

This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives.

The biomass furnace must be installed by an authorized service technician or contractor. Installation must be done in accordance with 

the installation instructions included with the product and all local and national building and fi re codes.

This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts 

installed from other manufacturers will nullify this warranty. warranty does not cover installations in commercial or industrial settings.

This limited warranty further does not cover any scratches, dents, corrosion or discoloring caused by excessive heat, abrasive and 

chemical cleaners nor chipping on porcelain enamel parts, nor any venting components used in the installation of the appliance.

This warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship provided that the 

product has been operated in accordance with the operation instructions and under normal conditions.

After the fi rst year, with respect to the President’s Lifetime Limited warranty, NAPOLEON® may, at its discretion, fully discharge all 

obligations with respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but 

defective part(s).

After the fi rst year, NAPOLEON® will not be responsible for installation, labour or any other costs or expenses related to the reinstallation 

of a warranted part, and such expenses are not covered by this warranty.

Notwithstanding any provisions contained in the President’s Lifetime Limited warranty, NAPOLEON’s responsibility under this warranty is 

defi ned as above and it shall not in any event extend to any incidental, consequential or indirect damages.

This warranty defi nes the obligations and liability of NAPOLEON® with respect to the NAPOLEON® biomass furnace and any other 

warranties expressed or implied with respect to this product, its components or accessories are excluded.

NAPOLEON® neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this 

product. NAPOLEON® will not be responsible for: over-fi ring, downdrafts, spillage caused by environmental conditions such as rooftops, 

buildings, nearby trees, hills, mountains, inadequate vents or ventilation, excessive venting confi gurations, insuffi cient makeup air, or 

negative air pressures which may or may not be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers, etc.

Any damages to appliance, combustion chamber, heat exchanger, plated trim or other component  due to water, weather damage, long 

periods of dampness, condensation, damaging chemicals or cleaners will not be the responsibility of NAPOLEON®.

All parts replaced under the President’s Limited Lifetime warranty Policy are subject to a single claim.

NAPOLEON® will provide replacement parts at a prorated value of the current retail price.

All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation.

The manufacturer may require that defective parts or products be returned or that digital pictures be provided to support the 

claim.  returned products are to be shipped prepaid to the manufacturer for investigation.  If a product is found to be defective, the 

manufacturer will repair or replace such defect.

Before shipping your appliance or defective components, your dealer must obtain an authorization number.  Any merchandise shipped 

without authorization will be refused and returned to sender.

Shipping costs are not covered under this warranty.

Additional service fees may apply if you are seeking warranty service from a dealer.

warranty labour allowance is only for the replacement of the warranted part.  Travel, diagnostic tests, shipping and other related 

charges are not covered by this warranty.

NAPOLEON® products are manufactured under the strict Standard of the world recognized ISO 9001 : 2008 quality 

Assurance Certifi cate.

NAPOLEON® products are designed with superior components and materials, assembled by trained craftsmen 

who take great pride in their work. The complete appliance is again thoroughly inspected by a qualifi ed technician 

before packaging to ensure that you, the customer, receives the quality product that you expect from NAPOLEON®.

The following materials and workmanship in your new NAPOLEON® biomass furnace are warranted against defects 

for as long as you own the appliance. This covers: weld defects in the combustion chamber and heat exchangers, 

ceramic glass (thermal breakage only), ash drawer and iron castings.* Perforations caused by metal scalings for a 

period of fi ve years.

Electrical (110v) components and wearable parts such as blowers, thermal switch, switches, wiring, fi rebrick, 

stainless steel baffl e retainer, secondary air tubes, and gasketing are covered and NAPOLEON® will provide 

replacement parts free of charge during the fi rst and second year of the limited warranty.* 

Labour related to warranty repair is covered free of charge during the fi rst year. repair work, however, requires 

the prior approval of an authorized company offi cial. Labour costs to the account of NAPOLEON® are based on a 

predetermined rate schedule and any repair work must be done through an authorized NAPOLEON® dealer.

Note that metal scaling is a normal occurrence during the lifetime of the fi rebox, but is greatly accelerated by the 

exposure to moisture, over fi ring and lack of preventative maintenance.  Evidence of either of these conditions voids 

warranty.

Parts such as fi rebricks, gaskets and baffl es should routinely be removed by the operator as part of the regular 

service and therefore, any warranty replacement of these parts does not qualify for any labour allowances.

* Construction of models vary. warranty applies only to components included with your specifi c appliance.

NAPOLEON® BIOmASS FurNACE PrESIdENT’S LIFETImE LImITEd wArrANTy

CONdITIONS ANd LImITATIONS

ALL SPECIFICATIONS ANd dESIgNS ArE SuBJECT TO CHANgE wITHOuT PrIOr NOTICE duE TO ON-gOINg PrOduCT 

ImPrOvEmENTS. NAPOLEON® IS A rEgISTErEd TrAdEmArk OF wOLF STEEL LTd. PATENTS u.S. 5.303.693.801 - CAN. 

2.073.411, 2.082.915. © wOLF STEEL LTd.

rev. 02.07.12

Содержание HMF100













































Отзывы: