background image

66

W415-0899 / B / 03.13.12

17.0 WARRANTY

NAPOLEON® warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is not necessary. Simply 
provide your proof of purchase along with the model and serial number to make a warranty claim. NAPOLEON® reserves the right to have its 
representative inspect any product or part thereof prior to honouring any warranty claim. Provided that the purchase was made through an authorized 
NAPOLEON® dealer your appliance is subject to the following conditions and limitations:
Warranty coverage begins on the date of original installation. 
This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives.
The gas appliance must be installed by a licensed, authorized service technician or contractor. Installation must be done in accordance with the installation 
instructions included with the product and all local and national building and 

fi

 re codes.   

This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed from 
other manufacturers will nullify this warranty.
This limited warranty further does not cover any scratches, dents, corrosion or discoloring caused by excessive heat, abrasive and chemical cleaners nor 
chipping on porcelain enamel parts, mechanical breakage of PHAZER™ logs and embers.
This warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship provided that the product has been 
operated in accordance with the operation instructions and under normal conditions.
After the 

fi

 rst year, with respect to this President’s Lifetime Limited Warranty, NAPOLEON® may, at its discretion, fully discharge all obligations with 

respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but defective part(s).
NAPOLEON® will not be responsible for installation, labour or any other expenses related to the reinstallation of a warranted part and such expenses are 
not covered by this warranty.
Notwithstanding any provisions contained in the President’s Lifetime Limited Warranty, NAPOLEON’S responsibility under this warranty is de

fi

 ned as 

above and it shall not in any event extend to any incidental, consequential or indirect damages.
This warranty de

fi

 nes the obligations and liability of NAPOLEON® with respect to the NAPOLEON® gas appliance and any other warranties expressed or 

implied with respect to this product, its components or accessories are excluded.
NAPOLEON® neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product. 
NAPOLEON® will not be responsible for: over-

fi

 ring, downdrafts, spillage caused by environmental conditions such as rooftops, buildings, nearby trees, 

hills, mountains, inadequate vents or ventilation, excessive venting con

fi

 gurations, insuf

fi

 cient makeup air, or negative air pressures which may or may not 

be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers, etc.
Any damages to the appliance, combustion chamber, heat exchanger, plated trim or other components due to water, weather damage, long periods of 
dampness, condensation, damaging chemicals or cleaners will not be the responsibility of NAPOLEON®.
All parts replaced under the President’s Limited Lifetime Warranty Policy are subject to a single claim.
During the 

fi

 rst 10 years NAPOLEON® will replace or repair the defective parts covered by the lifetime warranty at our discretion free of charge.  From 10 

years to life, NAPOLEON® will provide replacement parts at 50% of the current retail price.
All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation.
The manufacturer may require that defective parts or products be returned or that digital pictures be provided to support the claim.  Returned products are 
to be shipped prepaid to the manufacturer for investigation.  If a product is found to be defective, the manufacturer will repair or replace such defect.
Before shipping your appliance or defective components, your dealer must obtain an authorization number.  Any merchandise shipped without 
authorization will be refused and returned to sender.
Shipping costs are not covered under this warranty.
Additional service fees may apply if you are seeking warranty service from a dealer.
Warranty labour allowance is only for the replacement of the warranted part.  Travel, diagnostic tests, shipping and other related charges are not covered 
by this warranty.

2.1B

NAPOLEON® products are manufactured under the strict Standard of the world recognized ISO 9001 : 2008 Quality Assurance 

Certi

fi

 cate.

NAPOLEON® products are designed with superior components and materials assembled by trained craftsmen who take great 

pride in their work. The burner and valve assembly are leak and test-

fi

 red at a quality test station. The complete appliance is 

again thoroughly inspected by a quali

fi

 ed technician before packaging to ensure that you, the customer, receives the quality 

product that you expect from NAPOLEON®.

The following materials and workmanship in your new NAPOLEON® gas appliance are warranted against defects for as long as 
you own the appliance. This covers: combustion chamber, heat exchanger, stainless steel burner, phazer™ logs and embers, rocks, 
ceramic glass (thermal breakage only), gold plated parts against tarnishing, porcelainized enameled components and aluminum 
extrusion trims.*
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves, thermal switch, switches, wiring, remote 
controls, ignitor, gasketing, and pilot assembly are covered and NAPOLEON® will provide replacement parts free of charge during 
the 

fi

 rst year of the limited warranty.*

Labour related to warranty repair is covered free of charge during the 

fi

 rst year. Repair work, however, requires the prior approval of 

an authorized company of

fi

 cial. Labour costs to the account of NAPOLEON® are based on a predetermined rate schedule and any 

repair work must be done through an authorized NAPOLEON® dealer.
* Construction of models vary. Warranty applies only to components included with your speci

fi

 c appliance.

NAPOLEON® GAS APPLIANCE PRESIDENT’S LIFETIME LIMITED WARRANTY

CONDITIONS AND LIMITATIONS

ALL SPECIFICATIONS AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT 

IMPROVEMENTS.  NAPOLEON® IS A REGISTERED TRADEMARK OF WOLF STEEL LTD.

Содержание BGD36CFNTR





































































Отзывы: