NAL RESEARCH CORPORATION A3LA-RG Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 119

background image

NAL Research Corporation (451-93156-009A)

21

Command entries with invalid syntax typically respond with ERROR. Command entries of valid syntax

with an out-of-range parameter can respond in one of three following manners:



Disallow out-of-range entry and respond with ERROR



Disallow out-of-range entry and respond with OK



Disallow out-of-range entry, accept the closest in-range value, and respond with OK

A.7 Hardware Failure Reporting

If the A3LA-RG detects a hardware problem during initialization, it may be unable to function correctly.

The A3LA-RG notifies the DTE of this situation by issuing an unsolicited result code at the end of
initialization:

HARDWARE FAILURE: <subsys>,<error>

where <subsys> identifies the software subsystem that detected the error, and <error> is the subsystem
specific error code. Any AT commands that cannot be handled in the failure condition will terminate with

result code 4 (“ERROR”).

A.8 Command Set Description

A.8.1 AT – Attention Code

This is the prefix for all commands except A/ and +++. When entered on its own, the A3LA-RG
will respond OK.

A.8.2 A/ – Repeat Last Command

Repeat the last command issued to the A3LA-RG unless the power was interrupted or the unit is
reset. A/ is not followed by <CR>.

A.8.3 +++ – Escape Sequence

The escape sequence is used to transfer from in-call data mode to in-call command mode
without disconnecting from the remote modem. After a pause, the A3LA-RG will respond with
OK. Register S2 can be used to alter the escape character from +, the factory default, to any
hexadecimal value in the range 0 to 255.

A.8.4 En – Echo

Echo command characters.

0

Characters are not echoed to the DTE

1

Characters are echoed to the DTE (default)

A.8.5 On – Online

Enter in-call data mode. This is used to return to in-call data mode from in-call command mode

using an existing connection. An error is reported if on-hook.

0

Switch from in-call command mode to in-call data mode
Any value for n accepted

A.8.6 Qn – Quiet Mode

Control A3LA-RG responses.

0

A3LA-RG responses are sent to the DTE (default)

«
...
19
20
21
22
23
...
»

Содержание A3LA-RG
























































































































Отзывы:

Нет отзывов

Похожие инструкции для A3LA-RG

Бренд: Westermo Страницы: 18

Photo Backup Stick Universal

Бренд: Paraben Страницы: 10

Бренд: Paradyne Страницы: 2

Бренд: Sagem Страницы: 36

Бренд: Spectrum Страницы: 4

Бренд: C-motech Страницы: 19

Бренд: Access Страницы: 3

Бренд: Raymar Страницы: 26

FASTRACK M13006B

Бренд: M2M Страницы: 2

Бренд: Zte Страницы: 9

Бренд: Tainet Страницы: 109

Бренд: Navini Networks Страницы: 42

Бренд: Data-Linc Group Страницы: 10

Бренд: Teka Страницы: 72

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 184

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды