NAL RESEARCH CORPORATION A3LA-RG Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 119

NAL RESEARCH CORPORATION A3LA-RG Скачать руководство пользователя страница 83

NAL Research Corporation (451-93156-009A)

83

period of inactivity, it will retry a set number of times, after which it will force a registration.

The modem is registered to the Iridium network by dialing a dummy number. The forced
registration will not occur during a data connection because it is assumed that the modem is
registered.

<mode> takes the following values:

0 Disable the MPT forced registration functionality.
1 Enable the MPT forced registration functionality.

Read Command: ^MPTFR?
Query the current modem power toggle forced registration.. The response is in the form:

^MPTFR: <mode>

Test Command: ^MPTFR=?

List the supported modem power toggle forced registration. The response is in the form:

^MPTFR: (supported <mode>s)

A.8.138 ^MPTNC- Modem Power Toggle Not in Data Connection

Exec Command: ^MPTNC =

[<mode>]

Enable or disable the modem power toggle functionality out of a data connection. When not in a
data connection, after there has been a two minute period of inactivity, there will be a check
sent to determine if the modem is still responding. If it is not, the modem will power cycle and
return in command mode.

<mode> takes the following values:

0 Disable the MPT functionality out of a data call.
1 Enable the MPT functionality out of a data call.

Read Command: ^MPTNC?
Query the current modem power toggle not data connection mode. The response is in the form:

^MPTNC: <mode>

Test Command: ^MPTNC=?
List the supported modem power toggle not data connection modes. The response is in the
form:

^MPTNC: (supported <mode>s)

A.8.139 ^MSB – Motion Sensor Begin

Exec Command: ^MSB=<m>,<s>
This determines the number of minutes to look for motion for before the unit wakes up.

<m>: Number of minutes to wait to determine movement. The range is from 0 to 60. The

value of 0 means that the unit wakes up after sensing a single motion. Default is 3.

<s>: Sensitivity. How vigorous and consistent the motion must be every minute for the unit

to determine it is in motion. The range is 1 to 26 where 1 requires the least motion and

26 requires the most motion.

Read Command: ^MSB?

«
...
81
82
83
84
85
...
»

Содержание A3LA-RG
























































































































Отзывы:

Нет отзывов