NAL RESEARCH CORPORATION A3LA-RG Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 119

NAL RESEARCH CORPORATION A3LA-RG Скачать руководство пользователя страница 8

NAL Research Corporation (451-93156-009A)

8

IMPORTANT: Never feed supply voltage into the active GPS antenna. Always use the bias

voltage supplied by the A3LA-RG SMA antenna connector to power an active GPS antenna.
Feeding voltage to the GPS antenna other than the provided bias voltage will permanently
damage the A3LA-RG.

2.0 SPECIFICATIONS

2.1 Mechanical Specifications

Dimensions:

102 mm x 61 mm x 24 mm (4.0” x 2.43” x 0.95”)

Weight:

201 g (7.1 ounces)

Multi-Interface Connector:

25-Pin Male D-Sub

Iridium Antenna:

TNC Female Connector

GPS Antenna:

SMA Female Connector

SIM Chip Reader:

Located beneath a cover plate on top of the A3LA-RG

Status Display:

Four LEDs

Cooling:

Convection

Enclosure:

Aluminum/EMI shielding

2.2 RF Specifications

Operating Frequency:

1616 to 1626.5 MHz

Duplexing Method:

TDD

Multiplexing Method:

TDMA/FDMA

Link Margin:

12 dB average

Average Power during a Transmit Slot (Max):

7W

Average Power during a Frame (Typical):

0.6W

Receiver Sensitivity at 50



(Typical): –118 dBm

2.3 Electrical Specifications

Main Input Voltage Range:

+4.0V to +5.4V or +5.0V to +32.0V

Average Standby Current:

~175mA @ 5.0VDC (with +5.0V to +32.0V setup)

Average Data Call Current:

~420mA @ 5.0VDC (peak of 2A)

NOTE: The power requirements apply to DC power measured at the A3LA-RG multi-
interface connector input. The average data call current may vary depending on the field-
of-view between the modem antenna and the Iridium satellite.

2.4 Environmental Specifications

Operating Temperature Range: –30

o

C to +70

o

C (–22

o

F to +158

o

F)

Operating Humidity Range:

< 75% RH

Storage Temperature Range:

–40

o

C to +85

o

C (–40

o

F to +185

o

F)

Storage Humidity Range:

< 93% RH

2.5 Data I/O Specifications

Dial-Up Data/RUDICS: 2.4 Kbits/sec (average)

Direct Internet:

2.4 Kbits/sec (average)

«
...
6
7
8
9
10
...
»

Содержание A3LA-RG
























































































































Отзывы:

Нет отзывов