NAL RESEARCH CORPORATION A3LA-RG Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 119

NAL RESEARCH CORPORATION A3LA-RG Скачать руководство пользователя страница 80

NAL Research Corporation (451-93156-009A)

80

<n>:

0 URC is not displayed
1 URC is displayed. ^AAI:1 is displayed when auto answering starts and ^AAI:0 is

displayed when auto answering is finished whether or not it was successful.

Read Command: ^AA?
Queries the current setting

Test Command: ^AA=?
Returns the accepted values

A.8.126 ^AD – Auto Dial

Exec Command: ^AD=<enabled>,<number>
This command enables or disables auto dialing. If auto dialing is enabled, the A3LA-RG will go

into auto dial mode when the DTR line is brought low and will go back to command mode when

the DTR line is brought high again. While in auto dial mode, the A3LA-RG will not respond to AT
commands. Instead, the A3LA-RG will continuously dial the number that is setup for auto
dialing. The ^ADR command controls the retry delay in between dial attempts.
<enabled>:

0 Do not auto dial when the DTR line is low (default)
1 Auto dial when the DTR line is low

<number>: The phone number to dial. The number must be enclosed in double quotes and
cannot be more than 20 characters long.

A.8.127 ^ADR – Auto Dial Retry

Exec Command: ^ADR=<delay>

This command sets the time to delay in between dial attempts in auto dial mode.
<delay>: The number of seconds to delay. The value must be between 5 and 255 seconds.

A.8.128 ^CCOP – Change Crypto Officer Password (Encryption)

Exec Command: ^CCOP=<old>,<new>
Change the Crypto Officer’s password from factory-set/old value to new value. The password

must include all printable keyboard characters. The password will not be reset by AT command
&F. When the A3LA-RG is set to echo, all entries are replaced with asterisks (*) instead of the
actual typed value. All passwords must be between 8 and 16 characters in length. The factory-
set password is ‘temp password’ and must be changed before encryption can be used.

<old>: Old password and must be enclosed by two single quotes (‘old password‘)
<new>: New password and must be enclosed by two single quotes (‘new password‘)

A.8.129 ^CMGEC – Clear SMS Encrypted Storage

This command is a synonym for ^SMSE for backward compatibility. See the ^SMSE command

for details.

A.8.130 ^FFW – Flash Firmware

Exec Command: ^FFW
Puts the firmware into flashing mode

«
...
78
79
80
81
82
...
»

Содержание A3LA-RG
























































































































Отзывы:

Нет отзывов