background image

13. WARRANTY

THIS EQUIPMENT HAS BEEN MANUFACTURED AND TESTED TO THE HIGHEST STANDARD AND 

ACCORDINGLY CARRIES THE FOLLOWING WARRANTY.

The NKD1 Fresh Water System Control Unit will be repaired at no charge for a period of 36 Months from the 
date of purchase should it be found, after examination, that the failure has been caused by faulty 
workmanship or materials. This is a back to base warranty. The Electrolytic Cell carries a 3 year warranty. 
*The warranty applicable to commercial application is limited to 12 months from the date of installation 
unless a commercial model is purchased then this is 24 months. 

13.1

Adverse operating conditions beyond the control of the manufacturer such as improper voltage or water 
pressure, excessive ambient temperature or any condition that adversely affects the performance of the 
equipment will render this warranty null and void.

13.2

Defective equipment must be returned to the manufacturer or dealer as soon as the purchaser becomes 
aware of the defect and all transport must be prepaid. Neither the manufacturer nor the dealer shall be 
responsible for any goods damaged in transit.

13.3

If after examination the equipment is found to be defective it will be repaired or replaced free of charge 
(other than transport costs which will be borne by the purchaser). However, if upon inspection of the 
equipment it is found that the terms of this warranty are not satis ed, then the usual charges of the 
manufacturer for repair or replacement will be made.

13.4

Any liability of the manufacturer pursuant to the Trade Practices Act 1974, as amended for a breach of a 
condition or warranty shall be limited to replacing or acquiring the equipment (or part thereof ) where the 
same has been supplied.

13.5

The maximum liability incurred by the manufacturer shall not in any case exceed the contract price for the 
equipment or the product parts or components thereof claimed to be defective. Further, the manufacturer 
shall not be liable for any loss, damage or delay directly or indirectly caused by any malfunction of or defect 
of or failure of the equipment other than as expressly provided in this warranty.

13.6

Products sold by the manufacturer are designed for use with swimming pool water balanced in accordance 
with the Langelier Saturation Index with a pH range of 6.8-7.8. Copper levels should not exceed 0.5ppm and 
the TDS level should not exceed 1200ppm.

13.7

The manufacturer will not be held liable for damage caused by, but not limited to, corrosion, scaling or 
stress.

13.8

The Warranty is void under the following circumstances:

• 

Installation is carried out incorrectly by any person other than a person authorised by us to do so.

• 

The Control Unit or Cell Electrode is serviced by any person other than a person authorised by us to do so.

• 

Correct TDS levels are not maintained at all times.

• 

The Control Unit is not protected from the elements.

• 

The Control Unit is not operated in a position/area with good ventilation.

• 

Water has been allowed to enter the Control Unit.

• 

Run in a commercial installation (these have a 1 year warranty on Control Unit and Cell Electrode unless a   

  commercial application is granted then this is 24 months).

• 

Insect infestation or penetration by dust, sand or other foreign particles inside the Control Unit.

• 

Damage beyond our control.

• 

Equipment that has been misused, neglected, damaged, repaired without authorisation or altered in any way.

• 

This warranty is applicable to workmanship and materials only.

• 

This warranty is not transferable under any circumstance.

• 

This system is for use in domestic swimming pools only. Used in commercial applications voids the

  Warranty unless a commercial application has been granted.

www.naked-pools.com

33

Содержание NKD1





































Отзывы: