N-Tron NT24k Скачать руководство пользователя страница 20

Страница: 20 / 132

(Revised 4-9-2013) NT24k Managed Industrial Ethernet Switch User Manual & Installation Guide Page 20 of 132

APPLYING POWER AND FAULT CONNECTIONS (Back View)

All NT24k can operate with one power supply, either AC or DC. The Rack Mount NT24k can accept up to
two power supply units. Each power supply can be AC or DC. Each low voltage DC Power supply includes
redundancy (two DC supplies).

The example below is shown from the back and includes a AC Power supply on the left and a DC
power supply on the right, looking from the back:

NT24k with DC Power Supply Installed:



Unscrew & Remove the DC Voltage Input
Plug from the Power Input Header



Install the DC Power Cables into the Plug
(observing polarity).



Plug the Voltage Input Plug back into the
Power Input Header.



Tightening torque for the terminal block
power plug is

0.5 Nm/0.368 Pound Foot.



Verify the Power LED stays ON.

Notes:



When a DC Power supply is installed, only one power supply must be connected to power for
minimal operation. For redundant power operation, V

and V

inputs must be connected to separate

DC Voltage sources. This device will draw current from both sources simultaneously. Use 16-28
gauge wire when connecting to the power supply.

Recommended 24V DC Power Supplies, similar to: N-Tron’s P/N

NTPS-24-1.5



Input AC 115/230V



Output DC 24-28V



Output Current 1.5A @ 24V

1.0A @ 28V



Power 36W



35 mm DIN-Rail Mountable



Dimensions: 45X75X91 mm

Содержание NT24k





































































































































Результаты поиска

Содержание NT24k

Отзывы:

Похожие инструкции для NT24k

Бренды по названию

Популярные бренды

N-Tron NT24k, Руководство пользователя

Результаты поиска

Содержание NT24k

Отзывы:

Похожие инструкции для NT24k

Бренды по названию

Популярные бренды