Mychef Bake Скачать руководство пользователя страница 32

Страница: 32 / 71

mychefcooking.com

For gas ovens this value should be 5 or 6 (see table below).

The other values remain unused.

NO.

MODEL

MODE

TSC_DISABLED,

Electric oven without TSC

TSC_1_CH

Reserved

TSC_2_CH

Electric oven with TSC (electric)

TSC_3_CH

Reserved

TSC_4_CH

Reserved

GAS_1_CH

Gas Oven with 1 burner

GAS_2_CH

Gas oven with 2 burners

GAS_3_CH

Reserved

GAS_4_CH

Reserved

Auto clean

The record 4 allows to configure the oven if the equipment has a self-cleaning system.

The AIR, AIR-S and UP oven ranges do not have self-cleaning.

The PRO and MASTER 1/1 electric oven ranges have non-recirculated self-cleaning.

The Master 6 2/1 electric and gas ovens have recirculated self-cleaning.

The MAX and MASTER 10 2/1 electric and gas oven ranges have extended recirculated self-
cleaning.

Gas ovens have recirculated self-cleaning.

NO.

MODEL

MODE

AUTOCLEAN_DISABLED,

Cleaning disabled

AUTOCLEAN_TABS_SETTING1

Recirculated cleaning

AUTOCLEAN_TABS_SETTING2

Non-recirculated cleaning

AUTOCLEAN_TABS_SETTING3

Extended recirculated cleaning

Fan configuration

The record 4 defines the configuration of the fan, which can be of different speeds or
controlled by the inverter.

The AIR oven ranges have 1 speed.

Содержание Bake








































































Результаты поиска

Содержание Bake

Отзывы:

Похожие инструкции для Bake

Бренды по названию

Популярные бренды

Mychef Bake, Техническое и сервисное руководство

Результаты поиска

Содержание Bake

Отзывы:

Похожие инструкции для Bake

Бренды по названию

Популярные бренды