Mychef Bake Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 71

background image

mychefcooking.com

TECHNICAL SUPPORT SERVICE MANUAL iCOOK | iBAKE | COOK | BAKE | SNACK | BAKERSHOP - DT.MS.CB.2202.2

20

2.3.2.

The oven does not start

If an oven does not start, the door sensor may not detect that the door is properly closed.

On COOK, BAKE, iCOOK and iBAKE ovens, place a magnet near the door sensor area. If
the oven responds and the motor and resistor start, the problem is that the door is too far
away from the strut.

Door sensor (COOK, BAKE, iCOOK and iBAKE)

If placing a magnet next to the door sensor does not start the oven, check that the door
sensor is connected properly and that no wires are loose or cut.

The BAKERSHOP and SNACK models are equipped with a mechanical micro switch. Check
by manually pressing the switch.

Door sensor (SNACK and BAKERSHOP)

Check the door sensor cable on the relay board.

«
...
18
19
20
21
22
...
»

Содержание Bake








































































Отзывы:

Нет отзывов

Похожие инструкции для Bake

Spacemaker WSM2700L

Бренд: GE Страницы: 28

Бренд: Waring Страницы: 4

Бренд: Waring Страницы: 13

42525 Multi-cook

Бренд: Gastroback Страницы: 30

Бренд: Barton Страницы: 6

Бренд: nedis Страницы: 36

Бренд: Quirky Страницы: 5

Бренд: TOPPOINT Страницы: 2

Бренд: ARENDO Страницы: 24

Бренд: HAMOKI Страницы: 5

Бренд: Guzzanti Страницы: 61

Бренд: GVA Страницы: 16

Бренд: Smeg Страницы: 16

VOLANO HERITAGE

Бренд: Van Berkel International Страницы: 36

element WCU103-01

Бренд: Vinotemp Страницы: 20

Teasmade STM201N

Бренд: Swann Страницы: 8

Бренд: Orbegozo Страницы: 31

Бренд: Hisense Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды