Multitech MMCModem GPRS Скачать руководство пользователя страница 30

Страница: 30 / 203

Chapter 5 – Call Control Commands

Multi-Tech Systems, Inc. Wireless GSM/GPRS AT Commands (Document Number S000293I)

SideTone Modification +SIDET

Description:

This command sets the level of audio feedback in the speaker (microphone feedback in the speaker).

Values: <val1>
0

SideTone is disabled

SideTone is enabled

<val2>

(default value 0 will be used if this parameter is not given)

0 db

- 6 db

- 12 db

- 18 db

Syntax:

AT+SIDET=<val1>,<val2>

Command

Possible responses

AT+SIDET=1,0 OK

Note: Command valid

AT+SIDET?
Note: Current value

+SIDET: 1,0
OK
Note: Command valid

AT+SIDET=? +SIDET:

(0-1),(0-3)

Initialize Voice Parameters +VIP

Description:

This command allows factory settings for voice parameters to be restored from EEPROM.

These voice parameters include:

•

Gain control (

+VGR

+VGT

commands)

•

Gain controller (

+WSVG

command)

•

Microphone mute control (

+CMUT

command)

•

Speaker & Microphone selection (

+SPEAKER

command)

•

Echo cancellation (

+ECHO

command)

•

Side tone modification (

+SIDET

command)

Values:

<n>

Restore all voice parameters.

Other values are not supported.

Syntax:

AT+VIP=<n>

Command

Possible responses

AT+VIP? +VIP:

AT+VIP=2
Note: Syntax error

+CME ERROR: 3

AT+VIP=1
Note: Restore the factory settings from EEPROM

OK
Note: The command has been executed

AT+VIP=1
Note: Restore the factory settings from EEPROM
with the current Echo cancellation algorithm
(different of the default algorithm).

CME ERROR: 519
Note: Reset the product to accept the new
algorithm.

AT+VIP=?
Note: List of supported <n>s

+VIP: (1)
OK

Содержание MMCModem GPRS












































































































































































































Результаты поиска

Содержание MMCModem GPRS

Отзывы:

Похожие инструкции для MMCModem GPRS

Бренды по названию

Популярные бренды

Multitech MMCModem GPRS, Справочное руководство

Результаты поиска

Содержание MMCModem GPRS

Отзывы:

Похожие инструкции для MMCModem GPRS

Бренды по названию

Популярные бренды