Multitech MMCModem GPRS Скачать руководство пользователя страница 56

Страница: 56 / 203

Chapter 8 – Phonebook Commands

Multi-Tech Systems, Inc. Wireless GSM/GPRS AT Commands (Document Number S000293I)

Avoid Phonebook Initialization +WAIP

Description:

This specific command allows the initialization of all phonebooks to be inhibited during subsequent
boots.

Values: <mode>

Normal initialization (with phonebooks)

No phonebook initialization

Syntax:

Command Syntax:

AT+WAIP=<mode>

Command

Possible responses

AT+WAIP?

Note: Current values ?

+WAIP:0
OK
Note: Default value (init phonebooks)

AT+WAIP=?
Note: Possible values ?

+WAIP: (0,1)
OK
Note: Disable / enable

AT+WAIP =1
Note: Inhibit initialization of phonebooks (next boot)

OK
Note: no answer

AT&W
Note: Save modifications in EEPROM

Caution:

The given value should be stored in EEPROM. Therefore, the AT&W command must be used to save the

new <mode> value.

Note:

No phonebook commands are allowed if +WAIP=1 (after boot). If a phonebook command is entered, a “+CME

ERROR: 3” is returned.

Delete Calls Phonebook +WDCP

Description:

This specific command deletes the calls listed in some phonebooks.

Values: <calls

phonebook>

“LD”

SIM (ME extended) Last dialing phonebook

“MC”

ME missed calls list phonebook

“RC”

ME received calls list phonebook

Syntax:

Command Syntax:

+WDCP=<calls phonebook>

Command

Possible responses

AT+WDCP? OK
AT+WDCP=?

Note: Possible values ?

+WDCP: ("LD","MC","RC")
OK
Note: Identifiers of the phonebooks supporting a list of calls

AT+WDCP=”LD”
Note: Delete all the content of Last Dialing phonebook.

OK
Note: Last Dialing phonebook is now empty.

Set Voice Mail Number +CSVM

Description:

This commands sets/gets and enables/disables the voice mail number in memory.

Values: <mode>

Disable the voice mail number

Enable the voice mail number

<number>

Phone number in ASCII format.

<type>

TON/NPI (Type of address byte in integer format).

Note:

The value is 145 if the dialing string includes the international access code character

‘+’. Otherwise, the value is 129. Example: A <type> value of 17 will be written as 145.

Syntax:

Command Syntax:

AT+CSVM=<mode>[,<number>[,<type>]]

Command

Possible responses

AT+CSVM?
Note: Get mail number

+CSVM: 1,”660”,129
OK Note: Voice mail number “660” is activated

AT+CSVM=?

Note: Possible values ?

+CSVM: (0-1),(129,145)
OK
Note: activation/deactivation and format 129 & 145 are supported

AT+CSVM=0,”888”,129
Note: Disable Voice Mail number and
change value to “888”.

Содержание MMCModem GPRS












































































































































































































Результаты поиска

Содержание MMCModem GPRS

Отзывы:

Похожие инструкции для MMCModem GPRS

Бренды по названию

Популярные бренды

Multitech MMCModem GPRS, Справочное руководство

Результаты поиска

Содержание MMCModem GPRS

Отзывы:

Похожие инструкции для MMCModem GPRS

Бренды по названию

Популярные бренды