Multitech MMCModem GPRS Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 203

background image

Chapter 9 – Short Messages Commands

Multi-Tech Systems, Inc. Wireless GSM/GPRS AT Commands (Document Number S000293I)

76

Message Overwriting +WMGO

Description:

The +CMGW command specifies a location in the SMS or Flash memory for the next SMS to be stored
when the +CMGW indicates a message is ready to be stored. The defined location is used only once:
+WMGO has to used again to perform another overwrite.

Important Notes:

•

If the external application specifies a free location and an incoming message is received before the

AT+CMGW command occurs, the product may store the incoming message at the specified available
location. If the user then issues an AT+CMGW command without changing the location with another
AT+WMGO, the received message will be overwritten.

•

The location number is not kept over a software reset.

Values:

<loc>

Location number of the SIM record to write or overwrite. The number depends on the SIM or

Flash memory capacity.

Syntax:

Command Syntx:

AT+WMGO= <loc>

Command

Possible responses

AT+CPMS?
Note: Check the storage area

+CPMS: “SM”,3,10,”SM”,3,10,”SM”,3,10

AT+CMGW=”+33146290800”<CR>

Hello how are you?

<ctrl-Z>

Note: Write a message in text mode

+CMGW: 4
OK

Note: Message stored in index 4 in the SIM

AT+WMGO=? +WMGO:

(1-10)

OK

Note: Possible values for the SIM

AT+WMGO=4

AT+CMGW=”+33146299704”<CR>

You are overwritten

<ctrl-Z>

+CMGW: 4
OK

Note: New Message stored in index 4

AT+WMGO? +WMGO:

4

OK

Note: The value was used, so re-initialization

AT+WMGO=4 OK
AT+CPMS=”SM”,”ME,””SM”

+CPMS: 3,10,0,99,3,10
OK

Note: Change the storage area from SIM to Flash

AT+WMGO? +WMGO:

(1-99)

OK

Note: Possible values for Flash

AT+WMGO? +WMGO:

0

OK

Note: We changed the storage area, so the value
was reinitialized

AT+WMGO=999

+CMS ERROR: 321

Note:

If the storage area is changed with the AT+CPMS command, the value of WMGO will be reset to

zero.

«
...
74
75
76
77
78
...
»

Содержание MMCModem GPRS












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MMCModem GPRS

DSL-302G - 8 Mbps DSL Modem

Бренд: D-Link Страницы: 11

Бренд: CS Страницы: 50

Бренд: Patton electronics Страницы: 24

Бренд: Ubee Страницы: 2

Бренд: OUMAN Страницы: 8

Бренд: BROSTREND Страницы: 13

Бренд: Ebyte Страницы: 11

Бренд: Ebyte Страницы: 17

Бренд: ADC Страницы: 68

Бренд: Tait Страницы: 38

Бренд: NETGEAR Страницы: 19

Бренд: NETGEAR Страницы: 61

Бренд: Square One Industries Страницы: 30

Бренд: Hughes Страницы: 42

Бренд: Zte Страницы: 8

Crocus G703 SHDSL

Бренд: Telindus Страницы: 22

Бренд: Training Research Страницы: 49

Бренд: Maestro Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды