Multitech MMCModem GPRS Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 203

background image

Chapter 15 – GPRS Commands

Multi-Tech Systems, Inc. Wireless GSM/GPRS AT Commands (Document Number S000293I)

151

Quality of Service Profile Requested +CGQREQ

Description:

This command allows the DTE to specify a Quality of Service Profile that is used when the modem
sends an Activate PDP Context Request message to the network.

The set command specifies a profile for the context identified by the local context identification
parameter, <cid>. Since this is the same parameter that is used in the

+CGDCONT

command, the

+CGQREQ command is effectively an extension to the +CGDCONT command. The QoS profile
consists of a number of parameters, each of which may be set to a separate value.

A special form of the set command, +CGQREQ= <cid>, causes the requested profile for context
number <cid> to become undefined.

The read command returns the current settings for each defined context. The test command returns
values supported as a compound value. If the modem supports several PDP types, the parameter value
ranges for each PDP type are returned on a separate line.

Values:

<cid>

Numeric parameter that specifies a particular PDP context definition

Range 1- 3

<precedence>

Numeric parameter that specifies the precedence class

0

Subscribed precedence - Subscribed by the Network by default if value is omitted

1

High priority. Service commitments shall be maintained ahead of precedence classes 2 & 3

2

Normal priority - Service commitments shall be maintained ahead of precedence class 3

3

Low priority - Service commitments shall be maintained after precedence classes 1 and 2

<delay>

Numeric parameter that specifies the delay class

0

Subscribed

1

Delay class 1

2

Delay class 2

3

Delay class 3

4

Delay class 4

Delay (maximum values)

Delay Class

SDU size: 128 bytes

SDU size: 1024 bytes

Mean Transfer
Delay (sec)

95 percentile Delay
(sec)

Mean Transfer Delay
(sec)

95 percentile Delay (sec)

0

Subscribed

Subscribed by the Nwk / default if value is omitted

1. (Predictive)

< 0.5

< 2

< 7

2. (Predictive)

< 5

< 25

< 15

< 75

3. (Predictive)

< 50

< 250

< 75

< 375

4. (Best Effort)

Unspecified

<reliabiliy>

0

Subscribed

1

Up to 1 000 (8 kbit/s)

2

Up to 2 000 (16 kbit/s)

3

Up to 4 000 (32kbit/s)

4

Up to 8 000 (64 kbit/s)

5

Up to 16 000 (188 kbit/s)

6

Up to 32 000 (256 kbit/s)

7

Up to 64 000 (512 kbit/s)

8

Up to 128 000 (1 024 kbit/s)

9

Up to 256 000 (2 048 kbit/s)

«
...
149
150
151
152
153
...
»

Содержание MMCModem GPRS












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MMCModem GPRS

Touchstone TM608

Бренд: Arris Страницы: 32

Бренд: ORANGE Страницы: 12

Бренд: Zte Страницы: 7

Бренд: ADTRAN Страницы: 2

Бренд: ADTRAN Страницы: 4

Бренд: ADTRAN Страницы: 88

Zlinx Xtreme ZXT24-RM

Бренд: B&B Electronics Страницы: 163

Бренд: Billow Technology Страницы: 43

Бренд: Zte Страницы: 36

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 58

Digital Business System

Бренд: Panasonic Страницы: 87

Бренд: Panasonic Страницы: 135

Бренд: Dynex Страницы: 2

Бренд: Yamaha Страницы: 108

Бренд: Telecom Страницы: 16

Бренд: Zte Страницы: 25

Verizon LT1000 2G

Бренд: Connected IO Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды