Multitech MMCModem GPRS Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 203

background image

Chapter 7 – Security Commands

Multi-Tech Systems, Inc. Wireless GSM/GPRS AT Commands (Document Number S000293I)

40

Chapter 7 – Security

Commands

Enter PIN +CPIN

Description:

This command enters the ME passwords (CHV1 / CHV2 / PUK1 / PUK2, etc.), that are required before
any ME functionality can be used.

CHV1/CHV2

is between

4

and

8

digits long,

PUK1/PUK2

is

only

8

digits

long.

If the user application tries to make an outgoing call before the SIM PIN code (CHV1) has been
confirmed, then the product will refuse the “ATD” command with a “+CME ERROR: 11” (SIM PIN
required).

The application is responsible for checking the PIN after each reset or power on - if the PIN was
enabled.

Values:

<pin>

is the Personal Identification Number. A four-digit number.

<puk>

is the Personal Unblocking Key needed to change the PIN. An eight-digit number.

Syntax:

AT+CPIN=<pin>

Command

Possible responses

AT+CPIN=1234
Note: Enter PIN

OK
Note: PIN code is correct

AT+CPIN=5678
Note: Enter PIN

+CME ERROR: 3
Note: Operation not allowed, PIN previously entered

After 3 unsuccessful attempts to enter the PIN (Personal Identification Number), the PUK (Personal
Unblocking Key) will be required.

PUK validation forces the user to enter a new PIN code as a second parameter and this will be the new
PIN code if PUK validation succeeds. CHV1 is then enabled if PUK1 is correct. The application
therefore uses this command:

AT+CPIN=<Puk>,<NewPin>

Command

Possible responses

AT+CPIN=00000000,1234
Note: Enter PUK and new PIN

+CME ERROR: 16
Note: Incorrect PUK

AT+CPIN=12345678,1234
Note: Enter PUK and new PIN, 2nd attempt

OK
Note: PUK correct, new PIN stored

To determine which code must be entered (or not), the following query command can be used:

AT+CPIN?

The possible responses are:

+CPIN: READY

ME is not pending for any password

+CPIN: SIM PIN

CHV1 is required

+CPIN: SIM PUK

PUK1 is required

+CPIN: SIM PIN2

CHV2 is required

+CPIN: SIM PUK2

PUK2 is required

+CPIN: PH-SIM PIN

SIM lock (phone-to-SIM) is required

+CPIN: PH-NET PIN

Network personnalisation is required

+CME ERROR: <err>

SIM failure (13) absent (10) etc.

Please note that in this case the mobile equipment does not end its response with the OK string.

The reCME ERROR: 13 (SIM failure) is returned after 10 unsuccessful PUK attempts. The SIM
card is then out of order and must be replaced by a new one.

«
...
38
39
40
41
42
...
»

Содержание MMCModem GPRS












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MMCModem GPRS

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 72

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 56

Бренд: OUMAN Страницы: 6

MT5656ZDX Series

Бренд: Multitech Страницы: 30

LandCell SMC-GPRS Series

Бренд: CalAmp Страницы: 84

Бренд: Belkin Страницы: 2

Бренд: Zoom Страницы: 2

Бренд: Zoom Страницы: 40

Бренд: Huawei Страницы: 3

Бренд: Tecnet Страницы: 2

Бренд: Kinpo Страницы: 28

Бренд: nawras Страницы: 29

EZ Connect SMC8414-2P-SIP

Бренд: SMC Networks Страницы: 2

Бренд: AIS Страницы: 14

Бренд: Hughes Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды