Multiplex MB-8-1 Скачать руководство пользователя страница 95

Страница: 95 / 178

Part Number STH034 3/12

OPERATION IN THE CLEAN/SANITIZE CYCLE

During the weekly cleaning/sanitize cycle, the

evaporator fan motor relay and the condenser fan

motor/compressor relay are de-energized. The relays

cannot energize until the clean/sanitize cycle is

complete. Upon completion of the clean/sanitize cycle,

the relays will energize, provided the conditions listed

in normal operation are satisfied.

ADAPTIVE DEFROST

After 3 hours of cumulative compressor run time, the

compressor will be de-energized for fifteen (15)

minutes.

HIGH TEMP ALARM

High temp alarm will display when product thermistor

is above 42ºF for 30 minutes and the following

conditions are satisfied:
•

3 hours since power is applied

•

1 hour since cleaning cycle

Error display will reset when the temperature reaches

41ºF or below

THERMISTOR FAILURE

If the microprocessor control board receives an open

or shorted cabinet thermistor signal, the following will

happen:

1. A fault is displayed on the LCD screen

- Cabinet sensor open

- Cabinet sensor shorted

2. The microprocessor will initiate a default

sequence for the refrigeration system - 12

minutes on, 3 minutes off.

3. The default cycle continues until the fault is

corrected or power is disconnected. Refer to

Cabinet Temperature Thermistor for diagnostic

procedures.

Содержание MB-8-1



















































































































































































Результаты поиска

Содержание MB-8-1

Отзывы:

Бренды по названию

Популярные бренды

Multiplex MB-8-1, Руководство техника

Результаты поиска

Содержание MB-8-1

Отзывы:

Бренды по названию

Популярные бренды