manualshive.com logo in svg

Multiplex MB-8-1, Руководство техника

Поделиться
Скачать
Multiplex MB-8-1 Скачать руководство пользователя страница 120

120

Part Number STH034 3/12

REACH-IN TEMPERATURE OUT OF RANGE - 
CHECK REFRIGERATION SYSTEM AND DOOR 
SEAL.

Temperature in reach-in unit above or below 

acceptable limits.
Above temperature limit:
•

Verify door is closed and door gasket is in place.

•

Reboot machine by moving toggle switch off/on.

•

Allow refrigeration system to run for 15 minutes 

and recheck temperature.

•

Refer to Refrigeration diagnostics.

Below temperature limit:
•

Check temperature setpoint.

•

Check thermistor.

•

Check compressor relay on relay circuit board.

HIGH PRODUCT TEMPERATURE - CHECK DUCT 
COOLING FAN

Product temperature is greater than 42 F. 
•

Verify the door was not left open or warm product 

was added. 

•

Reboot machine by moving toggle switch off/on.

•

Verify duct fan is operating.

•

Allow machine to run for 15 minutes then prime 

each product. 

•

If fault remains check duct temperature with a 

digital thermometer to determine if refrigeration or 

thermistor diagnostics need to be performed.

Содержание MB-8-1



















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды