Multiplex MB-8-1 Скачать руководство пользователя страница 121

Страница: 121 / 178

Part Number STH034 3/12

121

Refrigeration System Diagnostics

ANALYZING DISCHARGE PRESSURE OR
TEMPERATURE

1. Determine the ice machine operating conditions:



Air temperature entering condenser



Air temperature around ice machine



Water temperature entering water reservoir

2. Refer to 24-Hour Ice Production/Refrigeration

Pressure/Temperature Chart for ice machine

being checked.

Use the operating conditions determined in step 1 to

find the published normal discharge pressure/

temperature and compare to actual measurements.

3. Measure the actual discharge pressure/

temperature.

4. Compare the measurements (step 3) with the

published pressure/temperature (step 2).

Measurements will fall within the published range on

normally operating ice machine’s.

Discharge Pressure/Temperature High Checklist

Problem

Cause

Improper
installation

Refer to Installation procedures.

Restricted
condenser



air flow

Dirty air filter
High inlet air temperature
Condenser discharge air recirculation
Dirty condenser fins
Defective fan motor
Defective fan cycle control

Improper
refrigerant



charge

Overcharged
Non-condensable in system
Wrong type of refrigerant

Other

Non-OEM components in system
High side refrigerant line/component
restricted (before mid-condenser)

Содержание MB-8-1



















































































































































































Результаты поиска

Содержание MB-8-1

Отзывы:

Бренды по названию

Популярные бренды

Multiplex MB-8-1, Руководство техника

Результаты поиска

Содержание MB-8-1

Отзывы:

Бренды по названию

Популярные бренды