manualshive.com logo in svg

Multiplex MB-8-1, Руководство техника

Поделиться
Скачать
Multiplex MB-8-1 Скачать руководство пользователя страница 73

Part Number STH034 3/12

73

4. Soak the parts in cleaning solution, then rinse the 

parts thoroughly.

5. Soak the parts in sanitizing solution and allow to 

air dry.

6. Wipe the inner ice bin wall with cleaning solution, 

rinse and wipe dry. Repeat with sanitizer solution 

and allow to air dry.

7. Use a bottle brush and cleaning solution to clean 

the ice nozzle at bottom of ice bin. Rinse, wipe 

dry, repeat with sanitizer solution and allow to air 

dry.

8. Drain water from evaporator and reservoir 

through the evaporator/reservoir drain line and 

reinsert hose into hose clip.

9. Follow the chart and premix cleaner and water.

10. Remove top cover from the water reservoir, block 

up reservoir float and fill the evaporator and 

reservoir with cleaning solution. Remainder of 

solution will be used for hand cleaning. 

Amount of Luke Warm 

Water

Amount of  Cleaner 

Part Number 000000084

1 gallon (4 Liters)

4 ounces (120 ml)

Содержание MB-8-1



















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды