background image

Introduction 

Multibor — Podolog Suite 

is a series of devices from the 

Podolog 

lineup developed under the

 Multibor-Suite 

technology intended for 

intensive operation with significant workloads while providing the 

entire range of services in the fields of machine-assisted manicure and 

pedicure as well as for incrementing, modeling, and correction of 

artificial nails. 

The lineup of devices comprises the following models: 

•  Multibor – Podolog

•  Multibor – Podolog MAX

These models have different technical properties and configurations. 

Multibor — Podolog Suite 

is a milling cutter for masters of nail care 

(hereinafter, the 'Milling Cutter'). This is a microprocessor unit with 

separate programs for different types of operations and for different 

types of tools with automatic selection of preset programs and with 

digital adjustment for optimal mode of operation.  

3

PROFESSIONAL TOOLS

Before getting started, please read this User Guide carefully. 

Attention! 

The device has sufficient means of electronic protection, 

but no automation is able to provide 100% safety against unjustified, 

inept or destructive steps by the User. 

Please remember! 

Before you switch on the rotation, make sure that 

nothing stands in its way, the engine is free, there is a tool in the 

collet clamp, the collet clamp is locked, and the collet holds the tool 

firmly.

  

Caution! 

Mechanical defects in the entire device or in separate parts 

thereof and absence of its components as well as damaged or burnt 

engine or its power cable shall deprive the User of the opportunity of 

free repair and shall not impose any warranty obligations upon the 

Manufacturer. 

Please handle the device with due care and use it as prescribed. Do 

not allow for excessive workload and do not use it for operations the 

device is not intended for, and it will then serve you very well for 

years! 

Should you have any questions regarding the use of the device or 

should you put the device into such modes of operation where from 

you don't know the way out, please contact the Service Center. 

Service Center

www.multibor.eu

Содержание Podolog

























Отзывы: