background image

Preparing for work 

1. Unpack the Milling Cutter. If the device is brought from a cold 

place to a warmer place, it should be unpacked not earlier than after 
two hours.  

2. Place the power unit onto a plain, rigid, and stable surface such as 

a working desk. Select a position of the power unit in such a manner 
that its front panel can be seen in full and its controls can be easily 
accessed. Place the pod in the immediate vicinity of the power unit. 

3. Connect the power cable plug of the handheld milling cutter to 

the relevant jack at the front panel of the power unit. 

Attention! The plug has a ping and the jack has an inlet. This is the 

key to the correct connection; the relevant ping should get into the 
relevant inlet. 

4. Check if there is a tool or a standard temporary cover in the collet 

clamp of the handheld milling cutter. 

5. Never forget to make sure that the collet clamp is locked and that 

the collet holds the tool firmly and does not let it fall out. 

6. Take the tool with your fingers carefully and turn the shaft of the 

handheld milling cutter a few times. Make sure that the tool can 
rotate together with the collet and that the rotation is done freely 
without external noise and vibration. 

7. Put the handheld milling cutter onto the pod in such a manner 

that it does not block your access to the front panel of the power 
unit. 

Attention! It is not recommended to put the handheld milling cutter 

as well as any other tools and caps onto the upper lid of the power 
unit. Use the pod instead. 

8. Plug the power cable in the wall socket.  
9. The milling cutter is now ready for work.  

11

Changing the tools in the MAX configurations 

1. Switch off the tool rotation

2. Wait until the tool rotation stops completely

3. Use your hands to 

turn the upper part 

(orange color) into the 

"A" direction over 2 

clicks. One click is not 

enough since this is an 

intermediate position

4. Click twice until locked in

5. Extract the old tool

6. Set the new tool 

     into the clamp

7. Turn the clamp lock into the "B" direction over two clicks

Pedal 

The pedal is intended for activating and deactivating the rotation 

function with the help of a foot. Depending on the configuration 

option, the pedal may sometimes not be a part of the equipment 

supplied. However, users can purchase the pedal as a separate piece 

of equipment. 

Содержание Podolog

























Отзывы: