manualshive.com logo in svg

MTU 12V4000L32F, Руководство по эксплуатации

Поделиться
Скачать
MTU 12V4000L32F Скачать руководство пользователя страница 80

1.4510.193  – Knock Sensor Error A2

Red alarm. Initiated by anti-knock control.

Cause

Corrective action

No signal from this knock sensor.

1. Check cabling (→ Page 202).
2. Check sensor (tightening torque, damage), replace as necessary

(→ Page 203).

1.4510.194  – Knock Sensor Error A3

Red alarm. Initiated by anti-knock control.

Cause

Corrective action

No signal from this knock sensor.

1. Check cabling (→ Page 202).
2. Check sensor (tightening torque, damage), replace as necessary

(→ Page 203).

1.4510.195  – Knock Sensor Error A4

Red alarm. Initiated by anti-knock control.

Cause

Corrective action

No signal from this knock sensor.

1. Check cabling (→ Page 202).
2. Check sensor (tightening torque, damage), replace as necessary

(→ Page 203).

1.4510.196  – Knock Sensor Error A5

Red alarm. Initiated by anti-knock control.

Cause

Corrective action

No signal from this knock sensor.

1. Check cabling (→ Page 202).
2. Check sensor (tightening torque, damage), replace as necessary

(→ Page 203).

1.4510.197  – Knock Sensor Error A6

Red alarm. Initiated by anti-knock control.

Cause

Corrective action

No signal from this knock sensor.

1. Check cabling (→ Page 202).
2. Check sensor (tightening torque, damage), replace as necessary

(→ Page 203).

1.4510.198  – Knock Sensor Error A7

Red alarm. Initiated by anti-knock control.

Cause

Corrective action

No signal from this knock sensor.

1. Check cabling (→ Page 202).
2. Check sensor (tightening torque, damage), replace as necessary

(→ Page 203).

80 | Troubleshooting | MS150104/03E 2017-09

TIM-ID: 0000038611 - 005

Содержание 12V4000L32F




























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды