manualshive.com logo in svg

MTU 12V4000L32F, Руководство по эксплуатации

Поделиться
Скачать
MTU 12V4000L32F Скачать руководство пользователя страница 64

112410  – LO T-Exhaust A10

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Exhaust gas temperature of this
cylinder is too low in comparison
with weighted average.

1. Check igniter.
2. Check emission values (→ Page 47).
3. Check ignition timing (→ Page 176).
4. Check valve drive.
5. Check wiring on the ignition rail/ignition coil for thermal and

mechanical damage.

112411  – LO T-Exhaust B1

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Exhaust gas temperature of this
cylinder is too low in comparison
with weighted average.

1. Check igniter.
2. Check emission values (→ Page 47).
3. Check ignition timing (→ Page 176).
4. Check valve drive.
5. Check wiring on the ignition rail/ignition coil for thermal and

mechanical damage.

112412  – LO T-Exhaust B2

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Exhaust gas temperature of this
cylinder is too low in comparison
with weighted average.

1. Check igniter.
2. Check emission values (→ Page 47).
3. Check ignition timing (→ Page 176).
4. Check valve drive.
5. Check wiring on the ignition rail/ignition coil for thermal and

mechanical damage.

112413  – LO T-Exhaust B3

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Exhaust gas temperature of this
cylinder is too low in comparison
with weighted average.

1. Check igniter.
2. Check emission values (→ Page 47).
3. Check ignition timing (→ Page 176).
4. Check valve drive.
5. Check wiring on the ignition rail/ignition coil for thermal and

mechanical damage.

64 | Troubleshooting | MS150104/03E 2017-09

TIM-ID: 0000038611 - 005

Содержание 12V4000L32F




























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды