manualshive.com logo in svg

MTU 12V4000L32F, Руководство по эксплуатации

Поделиться
Скачать
MTU 12V4000L32F Скачать руководство пользователя страница 118

1.4540.055 – Factory CAL Error

Red alarm. Initiated by TecJet.

Cause

Corrective action

Hardware not ready for operation.

1. Restart TecJet.
2. Replace TecJet.

1.4540.056  – PWM Duty Cycle High Error

Red alarm. Initiated by TecJet.

Cause

Corrective action

TecJet setting is not correct.

u

Check TecJet setting.

1.4550.031  – A - Internal Fault

Red alarm. Initiated by throttle of cylinder bank A.

Cause

Corrective action

Hardware not ready for operation.

1. Restart throttle.
2. Replace throttle.

1.4550.032  – A - Stop commanded (Run/Stop)

Yellow alarm. Initiated by throttle of cylinder bank A.

Cause

Corrective action

Throttle setting is not correct.

u

Check throttle setting.

1.4550.033  – A - Input (Supply) Voltage Fault

Yellow alarm. Initiated by throttle of cylinder bank A.

Cause

Corrective action

Supply voltage has reached
maximum or minimum limit value.

1. Check supply voltage.
2. Check cabling (→ Page 202).

1.4550.034  – A - Position Error

Red alarm. Initiated by throttle of cylinder bank A.

Cause

Corrective action

Position specification and
feedback signal do not match .

1. Check mechanical system.
2. Restart throttle.

1.4550.035  – A - Temperature Sensor Fault

Red alarm. Initiated by ProAct of cylinder bank A.

Cause

Corrective action

Internal temperature sensor
faulty.

1. Restart throttle.
2. Replace throttle.

118 | Troubleshooting | MS150104/03E 2017-09

TIM-ID: 0000038611 - 005

Содержание 12V4000L32F




























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды