MSA FireHawk M7 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 56

MSA FireHawk M7 Скачать руководство пользователя страница 23

USING THE AIR MASK

Replacing the Batteries in the FireHawk M7 HUD

Replace the batteries in the FireHawk M7 HUD or I-
HUD when the low battery LED flashes. Use only rec-
ommended battery types. Change the batteries in a
non-hazardous area only. Failure to follow this warn-
ing can result in serious personal injury or death.

1. Unthread the battery cap (counter-clockwise) on the

FireHawk M7 HUD battery tube.

2. Remove the battery cartridge from the FireHawk M7

HUD.

3. Remove the batteries and discard.
4. Ensure that moisture or debris is not present in the

battery compartment.

5. Inspect the battery cartridge for signs of damage such

as corrosion on the battery terminals or cracks in the
cartridge. If the battery cartridge is damaged, replace
the cartridge immediately.

6. Insert three AAA alkaline batteries in the appropriate

locations on the cartridge. Follow the notations on the
cartridge to ensure proper battery orientation.

Use only Rayovac 824 LR03, Rayovac Ultrapro LR03,
Energizer E92, Energizer Industrial EN92, Duracell
MN2400, or Duracell Procell PC2400 alkaline batteries

in the FireHawk M7 HUD. Use of other batteries, or a
combination of batteries from different manufacturers,
will affect the performance of unit and void the
Intrinsic Safety Approval.

7. Insert the battery cartridge into the battery tube on the

FireHawk M7 HUD.

8. Before installing the battery cap, verify that the o-ring

is in place and free of damage and debris. If the o-ring
is missing or damaged, replace o-ring. Failure to do so
may allow moisture or contaminants into the battery
tube and cause the device to not function properly.

9. Thread the battery cap on to the battery tube of the

FireHawk M7 HUD (clockwise). Hand-tighten cap until
snug. Do not over-tighten battery cap.

10. As the battery cap makes contact with the battery car-

tridge, verify that the FireHawk M7 HUD display turns
on and goes through its start up sequence before
turning off. The yellow LED should not be flashing.

Replacing the Battery in the FireHawk M7 I-HUD

Replace the batteries in the FireHawk M7 HUD or I-
HUD when the low battery LED flashes. Use only rec-
ommended battery types. Change the batteries in a
non-hazardous area only. Failure to follow this warn-
ing can result in serious personal injury or death.

23

TAL 1705 (L) Rev. 18 - 10082858

Left Hand Lights

Right Hand Lights

G

G

G

76% to 100%

Full Cylinder, 3 Green Right Side LED

G

G

75% to 51%

3/4 Full Cylinder, 2 Green Right Side LED

Y

Y

34% to 50%

1/2 Full Cylinder, 2 Yellow Right Side LED

Flashing Continuously

R

33% to 0%

1/4 Full Cylinder, 1 Red Right Side LED

Flashing Continuously

Y

Low Battery

Left Side Yellow LED

Flashing Continuously

O

PASS Pre-Alarm

Orange Left Side LED

R

O

Evacuate

Red and Orange Left Side LED

Flashing Alternating

Chart 2: FireHawk I-HUD LED Patterns

«
...
21
22
23
24
25
...
»

Содержание FireHawk M7

























































Отзывы:

Нет отзывов