MQ Power WHISPERWATT Series Скачать руководство пользователя страница 4

Страница: 4 / 42

PAGE 4 — DCA15SPXU4F • OPERATION MANUAL — REV. #1 (02/10/17)

SAFETY INFORMATION

Do not operate or service the equipment before reading the

entire manual. Safety precautions should be followed at all

times when operating this equipment. Failure to read and

understand the safety messages and operating instructions

could result in injury to yourself and others.

SAFETY MESSAGES

The four safety messages shown below will inform you

about potential hazards that could injure you or others. The

safety messages specifi cally address the level of exposure

to the operator and are preceded by one of four words:

DANGER, WARNING, CAUTION

NOTICE.

SAFETY SYMBOLS

DANGER

Indicates a hazardous situation which, if not avoided,

WILL

result in

DEATH

SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided,

COULD

result in

DEATH

SERIOUS INJURY.

CAUTION

Indicates a hazardous situation which, if not avoided,

COULD

result in

MINOR

MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this

equipment will be referenced with hazard symbols which

may appear throughout this manual in conjunction with

safety messages.

Содержание WHISPERWATT Series











































Результаты поиска

Содержание WHISPERWATT Series

Отзывы:

Похожие инструкции для WHISPERWATT Series

Бренды по названию

Популярные бренды

MQ Power WHISPERWATT Series, Руководство по эксплуатации

Результаты поиска

Содержание WHISPERWATT Series

Отзывы:

Похожие инструкции для WHISPERWATT Series

Бренды по названию

Популярные бренды