MQ Power WHISPERWATT Series Скачать руководство пользователя страница 23

Страница: 23 / 42

DCA15SPXU4F • OPERATION MANUAL — REV. #1 (02/10/17) — PAGE 23

SETUP

CIRCUIT BREAKERS

Make sure to switch

ALL

circuit breakers to the

OFF

position prior to starting the engine.

LUBRICATION OIL

Fill the engine crankcase with lubricating oil through the

filler hole, but

DO NOT

overfill. Make sure the generator is

level and verify that the oil level is maintained between the

two notches (Figure 16) on the dipstick. See Table 7 for

proper selection of engine oil.

Figure 16. Engine Oil Dipstick

When checking the engine oil, be sure to check if the oil is

clean. If the oil is not clean, drain the oil by removing the

oil drain plug, and refill with the specified amount of oil as

outlined in the

Kubota Engine Owner’s Manual

. Oil should

be warm before draining.
Delo® engine oil is the recommended engine oil for this

generator. When replacing engine oil please refill using

Delo® 400 LE SAE 15W-40 (API CJ-4) engine oil.

Table 7. Recommended Motor Oil

FUEL CHECK

Refilling the Fuel System

This generator has an internal fuel tank (Figure 17) located

inside the enclosure and may also be equipped with a trailer

mounted fuel tank.

ALWAYS

fill the fuel tank with clean fresh

#2 diesel fuel. DO NOT

fill the fuel tank beyond its capacity.

Pay attention to the fuel tank capacity when replenishing

fuel. The fuel tank cap must be closed tightly after filling.

Handle fuel in a safety container. If the container does not

have a spout, use a funnel. Wipe up any spilled fuel

immediately.

Figure 17. Fuel Tank

DANGER

Fuel spillage on a

hot

engine can cause

fire

explosion

. If fuel spillage occurs,

wipe up the spilled fuel completely to

prevent fire hazards.

NEVER

smoke

around or near the generator.

CAUTION

ONLY properly trained personnel

who have read

and understand this section should refill the fuel tank

system.

Содержание WHISPERWATT Series











































Результаты поиска

Содержание WHISPERWATT Series

Отзывы:

Похожие инструкции для WHISPERWATT Series

Бренды по названию

Популярные бренды

MQ Power WHISPERWATT Series, Руководство по эксплуатации

Результаты поиска

Содержание WHISPERWATT Series

Отзывы:

Похожие инструкции для WHISPERWATT Series

Бренды по названию

Популярные бренды