MQ Power WHISPERWATT Series Скачать руководство пользователя страница 34

Страница: 34 / 42

PAGE 34 — DCA15SPXU4F • OPERATION MANUAL — REV. #1 (02/10/17)

ENGINE FAULT CODES

ENGINE MALFUNCTION/FAILURE DIAGNOSTIC

CODES

When a engine malfunction/failure has been

detected the engine will be shut down and

the error code will be displayed on the glow

plug warning lamp by a series of flashing

patterns.
The flashing patterns consist of a combination of one

or more

long

flashes and one or more

short

flashes.

Reference Table 11 for an explanation of the flashing

pattern and the associated countermeasures.

Table 11. Engine Fault Codes

Symptom

Fault Explanation

Indication

Solution

Engine Speed Too High

115% or more of the rated

engine speed

Long 1 Short 1

Adjust engine speed to

correct RPM.

Low Oil Pressure

Oil pressure switch on

7.1 PSI (49 kPa) Approx.

Engine Shutdown

Long 1 Short 2

Check engine oil level and

switch.

Low Battery Voltage

Insufficient Charge

Long 1 Short 3

Inspect or replace engine

alternator/voltage regulator.

High Water Temperature

Overheat, 234°F (112° C).

Approx., Engine Shutdown

Long 1 Short 4

Check coolant level and

radiator. Also check Temp

switch.

Incorrect Crank Rotation

Defective crank rotation

sensor, disconnection or short

circuit

Long 2 Short 1

Replace sensor, check wiring.

Engine will not start

Disconnection, short circuit

fuel solenoid

Long 2 Short 2

Replace fuel solenoid, check

wiring.

Water Temperature Icon

Always OFF

Water Temperature Sensor

Disconnected

Long 2 Short 4

Check wiring or replace

sensor

Temperature Icon Always

Water Temperature Sensor

Short

Long 2 Short 5

Check wiring or replace

sensor.

Abnormal Battery Voltage

No Charge, cable

disconnected

Long 2 Short 6

Check or replace battery

and engine alternator. Check

wiring.

No Cranking

Regulator voltage exceeds

18 VDC or more

Long 2 Short 7

Check or replace voltage

regulator and battery

Содержание WHISPERWATT Series











































Результаты поиска

Содержание WHISPERWATT Series

Отзывы:

Похожие инструкции для WHISPERWATT Series

Бренды по названию

Популярные бренды

MQ Power WHISPERWATT Series, Руководство по эксплуатации

Результаты поиска

Содержание WHISPERWATT Series

Отзывы:

Похожие инструкции для WHISPERWATT Series

Бренды по названию

Популярные бренды