MQ Power WHISPERWATT Series Скачать руководство пользователя страница 37

Страница: 37 / 42

DCA15SPXU4F • OPERATION MANUAL — REV. #1 (02/10/17) — PAGE 37

Troubleshooting (Engine) - continued

Symptom

Possible Problem

Solution

Low engine power output and low speed,

black exhaust smoke.

Air fi lter blocked?

Clean or replace air fi lter.

Incorrect valve clearances?

Adjust valves per engine specifi cation.

Malfunction at injector?

See engine manual.

Engine overheats.

Too much oil in engine crankcase?

Drain off engine oil down to uppermark on
dipstick.

Entire cooling air system contaminated/

blocked?

Clean cooling air system and cooling fi n

areas.

Fan belt broken or elongated?

Change belt or adjust belt tension.

Coolant insuffi cient?

Replenish coolant.

Radiator net or radiator fi n clogged with dust? Clean net or fi n carefully.
Fan, radiator, or radiator cap defective?

Replace defective part.

Thermostat defective?

Check thermostat and replace if necessary.

Head gasket defective or water leakage?

Replace parts.

TROUBLESHOOTING ENGINE (CONTINUED)

Содержание WHISPERWATT Series











































Результаты поиска

Содержание WHISPERWATT Series

Отзывы:

Похожие инструкции для WHISPERWATT Series

Бренды по названию

Популярные бренды

MQ Power WHISPERWATT Series, Руководство по эксплуатации

Результаты поиска

Содержание WHISPERWATT Series

Отзывы:

Похожие инструкции для WHISPERWATT Series

Бренды по названию

Популярные бренды