Movacolor MC-BALANCE Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 49

Movacolor MC-BALANCE Скачать руководство пользователя страница 34

MC-Balance manual

31

General

The hopper loader is only activated when the motor is On .

Emergency stop.

To stop the hopper loader during production go to the HOPPER LOADER <menu> and switch the
ME or MV system to

OFF

.

Hopper loader settings

This part of the manual describes how to configure the hopper loader. For further technical
information about the hopper loader consult the specific hopper loader manual.

There are four ways to fill the hoppers:

1.  Manual
2.  Automatic with ME hopper loader
3.  Automatic with MV hopper loader
4.  Automatic with EX external hopper loader in combination with the support frame.

Manual

Open the hopper lid and fill the hopper by hand. (filling will be detected automatically)
The message “Low hopper level” appears when the hopper is empty.
(default 700 gr. In CONFIGURATIONS <menu>)

ME hopper loader (Movacolor hopper loader operated by compressed air)

Highlighted Parameters are factory settings.

MV hopper loader (Movacolor hopper loader operated by vacuum)

Highlighted Parameters are factory settings.

ME FILLING SYSTEM

ME system  :    OFF/ON
Fill time  :    30 sec
Alarm time :    31 sec
Alarm mode :    OFF/ON
Manual fill:    NO/YES

MV FILLING SYSTEM

MV system   :   OFF/ON
Fill time   :   20 sec
Empty time  :   05 sec
Fill cycles :   3  x
Alarm cycles:   10 x
Alarm mode :    OFF/ON
Manual fill:    NO/YES

ME system:

Switch ON / OFF the ME hopper loader system

Fill time:

Fill time [sec.], during this time the system blows material into the hopper of the
dosing unit.

Alarm time:

Fill Alarm [sec.], if the hopper weight is not above the 800gr. within this time, the
alarm starts. The alarm time can not set lower than the fill time.

Alarm mode:

ME hopper loader is ON / OFF during fill alarm.

ON

= ME Hopper loader stays activated during a filling alarm.

OFF

= ME Hopper loader will be deactivated during a filling alarm.

Manual fill:

Yes = starting filling immediately;

No = stop filling immediately

Only visible with controller in STOP mode.

The Manual filling function can be used for example to fill the hopper before start
of production.

MV system:

Switch ON / OFF the MV hopper loader system

Fill time:

Fill time [sec.], during this time the MV system sucks material into the vacuum
chamber.

Empty time:

Empty time [sec.], during this time the cone that closes the chamber will open
and material falls down into the hopper of the dosing unit.

Fill cycles:

Number of extra fill cycles after the hopper weight is above the 800gr. again

Alarm cycles:

Number of idle fill cycles before fill alarm. The number of alarm cycles needs to
be more than the number of Fill. cycles.

Alarm mode:

MV hopper loader is ON / OFF during fill alarm.
ON

= ME Hopper loader stays activated during a filling alarm.

OFF

= ME Hopper loader will be deactivated during a filling alarm.

Manual fill:

Yes = starting filling immediately;

No = stop filling immediately

Only visible with controller in STOP mode.
The Manual filling function can be used for example to fill the hopper before start
of production.

«
...
32
33
34
35
36
...
»

Содержание MC-BALANCE


















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды